Skip to content
Please enter a keyword to search

  • IEC 62282-2:2012

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Fuel cell technologies - Part 2: Fuel cell modules

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  31-12-2021

    Language(s):  English - French, Spanish, Castilian

    Published date:  26-03-2012

    Publisher:  International Electrotechnical Committee

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Requirements
    5 Type tests
    6 Routine tests
    7 Markings and instructions
    Annex A (informative) - Additional information for the
            performance and evaluation of the tests
    Annex B (informative) - List of notes concerning
            particular conditions in certain countries
    Bibliography

    Abstract - (Show below) - (Hide below)

    IEC 62282-2:2012 provides the minimum requirements for safety and performance of fuel cell modules; it applies to fuel cell modules with or without an enclosure which can be operated at significant pressurization levels or close to ambient pressure. Deals with conditions that can yield hazards to persons and cause damage outside the fuel cell modules. This edition includes the following significant technical changes with respect to the previous edition:
    - inclusion of definitions for hazards and hazardous locations based on the IEC 60079 series;
    - modification of the general safety strategy and of the electrical components clause to reflect the needs for different application standards. Key word: fuel cell

    General Product Information - (Show below) - (Hide below)

    Committee TC 105
    Development Note Stability Date: 2015. (10/2012)
    Document Type Standard
    Publisher International Electrotechnical Committee
    Status Superseded
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    PD IEC/TS 62282-7-2:2014 Fuel cell technologies Test methods. Single cell and stack performance tests for solid oxide fuel cells (SOFC)
    BS EN 62282-3-1:2007 Fuel cell technologies Stationary fuel cell power systems. Safety
    05/30060689 DC : DRAFT JUN 2005 IEC 62282-3-1 - FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER PLANTS - SAFETY
    EN 62282-3-1 : 2007 FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    BS EN 62282-5-1:2012 Fuel cell technologies Portable fuel cell power systems. Safety
    PREN 50465 : DRAFT 2011 GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW
    I.S. EN 62282-3-1:2007 FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    IEC 62282-5-1:2012 Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety
    UNE-EN 62282-3-1:2011 Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety
    SAE AIR 6464 : 2013 EUROCAE/SAE WG80/AE-7AFC HYDROGEN FUEL CELLS AIRCRAFT FUEL CELL SAFETY GUIDELINES
    13/30276640 DC : 0 BS EN 62282-4-101 ED 1.0 - FUEL CELL TECHNOLOGIES - PART 4-101: FUEL CELL POWER SYSTEMS FOR PROPULSION FOR OTHER THAN ROAD VEHICLES AND AUXILIARY POWER UNITS - FUEL CELL POWER SYSTEMS FOR ELECTRICALLY POWERED INDUSTRIAL TRUCKS - SAFETY
    BS EN 62282-4-101:2014 Fuel cell technologies Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU). Safety of electrically powered industrial trucks
    IEC 62282-4-101:2014 Fuel cell technologies - Part 4-101: Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU) - Safety of electrically powered industrial trucks
    UNE-EN 62282-5-1:2013 Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety
    10/30173705 DC : DRAFT SEP 2010 BS EN 62282-5-1 - FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY
    11/30249911 DC : 0 BS EN 50465 - GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW
    07/30091745 DC : 0 BS IEC 62368 - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - SAFETY - REQUIREMENTS
    16/30354067 DC : 0 BS EN 62282-5-100 - FUEL CELL TECHNOLOGIES - PART 5-100: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY
    IEC 62282-3-1:2007 Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety
    EN 62282-5-1:2012 FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-5-1:2012)
    EN 62282-4-101:2014 Fuel cell technologies - Part 4-101: Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU) - Safety of electrically powered industrial trucks

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61025:2006 Fault tree analysis (FTA)
    IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
    CSA B51 : 2014 BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE
    IEC 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
    IEC 60050-151:2001 International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices
    IEC TS 62282-1:2013 Fuel cell technologies - Part 1: Terminology
    CSA C22.2 No. 60079.0 : 2015 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
    ISO 4672:1997 Rubber and plastics hoses Sub-ambient temperature flexibility tests
    IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
    ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
    IEC 60079-20-1:2010 Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data
    IEC 62040-1:2017 EXV UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: SAFETY REQUIREMENTS
    CGA 12.6 : M94(R1999) VEHICLE REFUELLING APPLIANCES
    EN 50178:1997 Electronic equipment for use in power installations
    CSA C22.2 No. 60529 : 2016 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE)
    SAE J 1739 : 2009 POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN DESIGN (DESIGN FMEA), POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN MANUFACTURING AND ASSEMBLY PROCESSES (PROCESS FMEA)
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC 62282-3-100:2012 Fuel cell technologies - Part 3-100: Stationary fuel cell power systems - Safety
    ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
    ISO 1402:2009 Rubber and plastics hoses and hose assemblies Hydrostatic testing
    ISO 1307:2006 Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses
    IEC 62061:2005+AMD1:2012+AMD2:2015 CSV Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems
    ISO 1436:2017 Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification
    ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
    ISO 23550:2011 Safety and control devices for gas burners and gas-burning appliances General requirements
    IEC 60730-1:2013+AMD1:2015 CSV Automatic electrical controls - Part 1: General requirements
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective