Skip to content
Please enter a keyword to search

  • IEEE 404-2012

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    IEEE Standard for Extruded and Laminated Dielectric Shielded Cable Joints Rated 2.5 kV to 500 kV

    Available format(s):  PDF

    Superseded date:  21-03-2023

    Language(s):  English

    Published date:  18-06-2012

    Publisher:  Institute of Electrical & Electronics Engineers

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. Overview
    2. Normative references
    3. Definitions
    4. Service conditions
    5. Ratings
    6. General requirements
    7. Design testing
    8. Routine production testing
    Annex A (informative) - Typical values of heat-shrinkable
            and multi-component cold-shrink joint component
            tests and sampling rates
    Annex B (informative) - Typical values of elastomeric
            taped joint component tests and sampling rates
    Annex C (informative) - DC test voltage reference
    Annex D (informative) - Bibliography

    Abstract - (Show below) - (Hide below)

    Sets up electrical ratings and test requirements of cable joints used with extruded and laminated dielectric shielded cables rated in preferred voltage steps from 2.5 kV to 500 kV. Also specifies test requirements for joint jacket seal devices and joint metallic-shield devices.

    General Product Information - (Show below) - (Hide below)

    Committee Insulated Conductors
    Development Note Supersedes IEEE DRAFT 404. (03/2007)
    Document Type Standard
    Publisher Institute of Electrical & Electronics Engineers
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    IEEE 141 : 1993 IEEE Recommended Practice for Electric Power Distribution for Industrial Plants
    IEEE 592-2007 REDLINE IEEE Standard for Exposed Semiconducting Shields on High-Voltage Cable Joints and Separable Connectors
    IEEE 1242-1999 IEEE Guide for Specifying and Selecting Power, Control, and Special-Purpose Cable for Petroleum and Chemical Plants
    IEEE DRAFT 1511 : D6.0 MAY 2000 DRAFT GUIDE FOR INVESTIGATING AND ANALYZING POWER CABLE, JOINT, AND TERMINATION FAILURES ON SYSTEMS RATED 5 KV THROUGH 46 KV
    IEEE 525-2007 IEEE Guide for the Design and Installation of Cable Systems in Substations
    IEEE 400.1-2007 IEEE Guide for Field Testing of Laminated Dielectric, Shielded Power Cable Systems Rated 5 kV and Above with High Direct Current Voltage
    TM 5-811-1 : V19950228 ARMY TECHNICAL MANUAL - ELECTRICAL POWER SUPPLY AND DISTRIBUTION
    IEEE DRAFT 525 : D15 2006 DESIGN AND INSTALLATION OF CABLE SYSTEMS IN SUBSTATIONS
    IEEE 400-2012 REDLINE IEEE Guide for Field Testing and Evaluation of the Insulation of Shielded Power Cable Systems Rated 5 kV and Above
    IEEE DRAFT 400.1 : D8 2006 FIELD TESTING OF LAMINATED DIELECTRIC, SHIELDED POWER CABLE SYSTEMS RATED 5 KV AND ABOVE WITH HIGH DIRECT CURRENT VOLTAGE
    IEEE 1816-2013 IEEE Guide for Preparation Techniques of Extruded Dielectric, Shielded Cables Rated 2.5 kV through 46 kV and the Installation of Mating Accessories
    IEEE 3001.5-2013 IEEE Recommended Practice for the Application of Power Distribution Apparatus in Industrial and Commercial Power Systems
    CSA C22.2 No. 272 : 2014 WIND TURBINE ELECTRICAL SYSTEMS
    CSA C22.3 No. 7 : 2015 UNDERGROUND SYSTEMS
    IEEE 241 : 1990 ELECTRIC POWER SYSTEMS IN COMMERCIAL BUILDINGS
    IEEE 400.4-2015 IEEE Guide for Field Testing of Shielded Power Cable Systems Rated 5 kV and Above with Damped Alternating Current (DAC) Voltage
    IEEE 1313.1-1996 IEEE Standard for Insulation Coordination - Definitions, Principles and Rules
    IEEE 82 : 2002 TEST PROCEDURE FOR IMPULSE VOLTAGE TESTS ON INSULATED CONDUCTORS
    IEEE 592-2018 IEEE Standard for Insulation Shields on Medium-Voltage (15 kV - 35 kV) Cable Joints and Separable Connectors

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 4325 : 2013 : REDLINE Standard Test Methods for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes
    ASTM D 4496 : 2013 Standard Test Method for D-C Resistance or Conductance of Moderately Conductive Materials
    ASTM D 4388 : 2013 Standard Specification for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes
    IEEE 4-1995 IEEE Standard Techniques for High-Voltage Testing
    IEC 60502-4:2010 Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV) - Part 4: Test requirements on accessories for cables with rated voltages from 6 kV (Um = 7,2 kV) up to 30 kV (Um = 36 kV)
    IEEE 575-1988 IEEE Guide for Application of Sheath-Bonding Methods for Single-Conductor Cables and the Calculation of Induced Voltages and Currents in Cable Sheaths
    IEEE 592-2007 REDLINE IEEE Standard for Exposed Semiconducting Shields on High-Voltage Cable Joints and Separable Connectors
    IEEE 82 : 2002 TEST PROCEDURE FOR IMPULSE VOLTAGE TESTS ON INSULATED CONDUCTORS
    IEEE 4-2013 IEEE Standard for High-Voltage Testing Techniques
    IEEE C37.09-1999 IEEE Standard Test Procedure for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis
    IEEE 575-2014 IEEE Guide for Bonding Shields and Sheaths of Single-Conductor Power Cables Rated 5 kV through 500 kV
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective