Skip to content
Please enter a keyword to search

  • IEEE C57.13.5-2009

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    IEEE Standard of Performance and Test Requirements for Instrument Transformers of a Nominal System Voltage of 115 kV and Above

    Available format(s):  PDF

    Superseded date:  04-02-2022

    Language(s):  English

    Published date:  30-12-2009

    Publisher:  Institute of Electrical & Electronics Engineers

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. Overview
    2. Normative references
    3. Definitions
    4. General
    5. Test conditions
    6. Classification of test
    7. Routine test procedures (applicable to instrument
        transformers)
    8. Routine test procedures (applicable to current
        transformers)
    9. Routine test procedures (applicable to voltage
        transformers)
    10. Type test procedures (applicable to instrument
        transformers)
    11. Type test procedure (applicable to current
        transformers)
    12. Special test procedures
    13. Identification of test sample in the type test
        report
    Annex A (normative) - Test code
    Annex B (informative) - Dielectric test performed at
            an altitude of 1000 m or less for instrument
            transformers designed for installation at
            altitudes greater than 1000 m
    Annex C (informative) - Dielectric tests, oil sampling,
            and other related measurements in the field
    Annex D (informative) - Internal arc protection for
            instrument transformers
    Annex E (normative) - Validity of type test reports
            and guidance for reviewing the design comparison
            report for the modified design
    Annex F (informative) - Rated voltage factor
    Annex G (normative) - Current transformers used for the
            detection of unbalance current of capacitor banks
    Annex H (informative) - Current transformers having
            transient performance requirements
    Annex I (informative) - Electrical endurance test,
            explanatory note
    Annex J (informative) - Bibliography

    Abstract - (Show below) - (Hide below)

    Pertains to single-phase instrument transformers of a nominal system voltage of 115 kV and above with capacitive insulation system for line-to-ground connection and for both indoor and outdoor application.

    General Product Information - (Show below) - (Hide below)

    Committee Transformers
    Document Type Standard
    Publisher Institute of Electrical & Electronics Engineers
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    CSA C60044-5:2007 INSTRUMENT TRANSFORMERS - PART 5: CAPACITOR VOLTAGE TRANSFORMERS
    CSA C60044-5 : 2007 : R2011 INSTRUMENT TRANSFORMERS - PART 5: CAPACITOR VOLTAGE TRANSFORMERS
    IEEE 1601-2010 IEEE Trial-Use Standard for Optical AC Current and Voltage Sensing Systems
    CSA C60044-1 : 2007 : R2011 INSTRUMENT TRANSFORMERS - PART 1: CURRENT TRANSFORMERS
    CSA C60044-1 : 2007 INSTRUMENT TRANSFORMERS - PART 1: CURRENT TRANSFORMERS
    IEEE 1861-2014 IEEE Guide for On-Site Acceptance Tests of Electrical Equipment and System Commissioning of 1000 kV AC and Above
    IEEE C57.13-2016 IEEE Standard Requirements for Instrument Transformers
    IEEE C37.241-2017 IEEE Guide for Application of Optical Instrument Transformers for Protective Relaying

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60270:2000+AMD1:2015 CSV High-voltage test techniques - Partial discharge measurements
    IEEE C57.19.100-2012 REDLINE IEEE Guide for Application of Power Apparatus Bushings
    EN 50052:2016 High-voltage switchgear and controlgear - Gas-filled cast aluminium alloy enclosures
    IEEE 4-1995 IEEE Standard Techniques for High-Voltage Testing
    NEMA 107:2016 Methods of Measurement of Radio Influence Voltage (RIV) of High Voltage Apparatus
    IEEE C57.19.01-2000 IEEE Standard Performance Characteristics and Dimensions for Outdoor Apparatus Bushings
    EN 50064 : 1989 COR 2007 WROUGHT ALUMINIUM AND ALUMINIUM ALLOY ENCLOSURES FOR GAS-FILLED HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR
    ASTM D 1275 : 2015 Standard Test Method for Corrosive Sulfur in Electrical Insulating Liquids
    IEEE 4-2013 IEEE Standard for High-Voltage Testing Techniques
    IEEE C62.11-2005 IEEE Standard for Metal-Oxide Surge Arresters for AC Power Circuits (> 1 kV)
    IEC 60044-6:1992 Instrument transformers - Part 6: Requirements for protective current transformers for transient performance
    ASTM D 1868 : 2013 : REDLINE Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems
    IEC 61181:2007+AMD1:2012 CSV Mineral oil-filled electrical equipment - Application of dissolved gas analysis (DGA) to factory tests on electrical equipment
    EN 50068 : 1991 COR 2007 WROUGHT STEEL ENCLOSURES FOR GAS FILLED HIGH VOLTAGE SWITCHGEAR AND CONTROLGEAR
    IEEE C57.13-2008 IEEE Standard Requirements for Instrument Transformers
    IEEE 693-2005 IEEE Recommended Practice for Seismic Design of Substations
    IEEE C57.106-2006 IEEE Guide for Acceptance and Maintenance of Insulating Oil in Equipment
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective