Skip to content
Please enter a keyword to search

  • ISO 75-3:2004

    Current The latest, up-to-date edition.

    Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s):  English, French

    Published date:  12-05-2004

    Publisher:  International Organization for Standardization

    Add To Cart

    Abstract - (Show below) - (Hide below)

    ISO 75-3:2004 specifies a method for the determination of the temperature of deflection under load of high-strength thermosetting laminates and compression-moulded long-fibre-reinforced plastics in which the fibre length is greater than 7,5 mm. The flexural stress used is not fixed, as in ISO 75-2, but is a fraction (1/1000) of the initial (room-temperature) flexural modulus of the material under test. This allows the method to be applied to materials with a wide range of flexural moduli.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes ISO 75 (04/2001) Supersedes ISO/DIS 75-3 (05/2004)
    Document Type Standard
    Publisher International Organization for Standardization
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    11/30229997 DC : 0 BS EN 14427 - LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION
    PREN 2719 : 200P1 AEROSPACE SERIES - POLYCARBONATE SHEET - TECHNICAL SPECIFICATION
    PREN 13160-7 : DRAFT 2014 LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS
    PREN 4243 : 200P1 AEROSPACE SERIES - CAST ACRYLIC SHEETS - TECHNICAL SPECIFICATION
    EN ISO 9093-2:2002 Small craft - Seacocks and through-hull fittings - Part 2: Non-metallic (ISO 9093-2:2002)
    DIN EN 13923:2006-02 Filament-wound FRP pressure vessels - Materials, design, manufacturing and testing
    EN 13160-7:2016 Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets
    NF EN ISO 10350-2 : 2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    ONORM EN 12245 : 2012 TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS
    DEFSTAN 93-111/1(2004) : 2004 FIBRE REINFORCED POLYMER COMPOSITE FOR BALLISTIC PROTECTION PURPOSES
    02/103631 DC : DRAFT MAY 2002 BS EN 14471 - CHIMNEYS - REQUIREMENTS AND TEST METHODS FOR SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS
    07/30165210 DC : 0 BS EN ISO 10350-2 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    BS 7825-3.1:1997 Calibration of rubber and plastics test equipment. Calibration schedules Thermal properties
    14/30301266 DC : 0 BS EN 13160-7 - LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS
    UNI CEN ISO/TS 24817 : 2011 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
    PREN ISO 75-1 : DRAFT 2012 PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD PART 1: GENERAL TEST METHOD (ISO/DIS 75-1:2012)
    DIN EN ISO 10350-2:2011-06 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    DIN EN 14427:2014-09 LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction
    BS EN ISO 4894-2:1999 Plastics. Styrene/acrylonitrile (SAN) copolymer moulding and extrusion materials Preparation of test specimens and determination of properties
    ISO/TS 24817:2006 Petroleum, petrochemical and natural gas industries Composite repairs for pipework Qualification and design, installation, testing and inspection
    BS EN 13280:2001 Specification for glass fibre reinforced cisterns of one-piece and sectional construction, for the storage, above ground, of cold water
    DIN EN 15274:2015-06 GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS
    I.S. EN 13160-7:2016 LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS
    I.S. EN 14427:2014 LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION
    I.S. EN 15274:2015 GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS
    I.S. EN 12245:2009 TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS
    14/30300568 DC : 0 BS EN 15274 - GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS
    17/30349214 DC : 0 BS EN ISO 21970-1 - PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS
    ESPECIFICACION UNE 0059:2017 Fiberglass reinforced polyester poles for overhead power distribution lines and telephony lines
    12/30238122 DC : 0 BS EN ISO 75-1 - PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 1: GENERAL TEST METHOD (ISO/DIS 75-1:2012)
    PREN 15269-20 : DRAFT 2017 EXTENDED APPLICATION OF TEST RESULTS FOR FIRE RESISTANCE AND/OR SMOKE CONTROL FOR DOOR, SHUTTER AND OPENABLE WINDOW ASSEMBLIES, INCLUDING THEIR ELEMENTS OF BUILDING HARDWARE - PART 20: SMOKE CONTROL FOR DOORS, SHUTTERS AND OPENABLE WINDOWS
    ISO 24817:2017 Petroleum, petrochemical and natural gas industries — Composite repairs for pipework — Qualification and design, installation, testing and inspection
    UNE-EN 13160-7:2017 Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets
    DIN EN 12245:2012-03 Transportable gas cylinders - Fully wrapped composite cylinders (includes Amendment A1:2011)
    UNE-EN ISO 75-1:2013 Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:2013)
    BS EN ISO 75-1:2013 Plastics. Determination of temperature of deflection under load General test method
    12/30260914 DC : 0 BS EN 4718 - AEROSPACE SERIES - POLYETHERKETONE WITH 55% CONTINUOUS GLASS FIBRE BY VOLUME (PEEK-GF55)
    DIN EN 15274 E : 2015 GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS
    BS EN ISO 10350-2:2011 Plastics. Acquisition and presentation of comparable single-point data Long-fibre-reinforced plastics
    EN ISO 10350-2:2011 Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2011)
    UNI EN ISO 10350-2 : 2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    UNI EN ISO 75-1 : 2013 PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 1: GENERAL TEST METHOD
    ONORM EN ISO 10350-2 : 2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    DIN EN 14427 E : 2014 LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION
    I.S. EN ISO 10350-2:2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
    UNI EN 14427 : 2014 LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION
    UNI EN 12245 : 2011 TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS
    ONORM EN 14427 : 2014 LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION
    DD CEN ISO/TS 24817:2011 Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection
    I.S. EN ISO 24817:2017 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION (ISO 24817:2017, CORRECTED VERSION 2018-01-01)
    PREN 15274 : DRAFT 2014 GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS
    14/30256269 DC : 0 BS EN ISO 24817 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
    ASTM D 5935 : 1996 Practice for Acquisition and Presentation of Comparable Single-Point Data (Withdrawn 1998)
    I.S. EN ISO 9093-2:2002 SMALL CRAFT - SEACOCKS AND THROUGH-HULL FITTINGS - PART 2: NON-METALLIC
    BS EN ISO 24817:2017 Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection
    BS EN ISO 9093-2:2002 Small craft. Seacocks and through-hull fittings Non-metallic
    DIN EN ISO 75-1:2013-08 PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 1: GENERAL TEST METHOD (ISO 75-1:2013)
    BS EN 13923:2005 Filament-wound FRP pressure vessels. Materials, design, manufacturing and testing
    BS EN 13160-7:2003 Leak detection systems General requirements and test methods for interstitial spaces, leak protecting linings and leak protecting jackets
    UNE-EN 15274:2015 General purpose adhesives for structural assembly - Requirements and test methods
    BS EN 14427:2014 LPG equipment and accessories. Transportable refillable fully wrapped composite cylinders for LPG. Design and construction
    UNE-EN 14427:2014 LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction
    UNE-EN ISO 10350-2:2011 Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2011)
    EN ISO 75-1:2013 Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:2013)
    ISO 10350:1993 Plastics Acquisition and presentation of comparable single-point data
    ONORM EN ISO 75-1 : 2013 PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 1: GENERAL TEST METHOD (ISO 75-1:2013)
    I.S. EN ISO 75-1:2013 PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 1: GENERAL TEST METHOD (ISO 75-1:2013)
    UNE-EN 12245:2009 Transportable gas cylinders - Fully wrapped composite cylinders
    12/30260913 DC : 0 BS EN 4717 - AEROSPACE SERIES - POLYETHERKETONE WITH 55% CONTINUOUS CARBON FIBRE BY VOLUME (PEEK-CF55)
    EN 14427:2014 LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction
    EN 13280:2001 Specification for glass fibre reinforced cisterns of one piece and sectional construction, for the storage, above ground, of cold water
    EN 15274:2015 General purpose adhesives for structural assembly - Requirements and test methods
    EN 13923:2005 Filament-wound FRP pressure vessels - Materials, design, manufacturing and testing
    EN 12245:2009+A1:2011 Transportable gas cylinders - Fully wrapped composite cylinders
    DD ISO/TS 24817 : 2006 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
    ABS 0063 : 2018 COR 2018 RULES FOR BUILDING AND CLASSING FACILITIES ON OFFSHORE INSTALLATIONS
    BS ISO 1268-8:2004 Fibre-reinforced plastics. Methods of producing test plates Compression moulding of SMC and BMC
    17/30359220 DC : 0 BS EN 15269-20 - EXTENDED APPLICATION OF TEST RESULTS FOR FIRE RESISTANCE AND/OR SMOKE CONTROL FOR DOOR, SHUTTER AND OPENABLE WINDOW ASSEMBLIES, INCLUDING THEIR ELEMENTS OF BUILDING HARDWARE - PART 20: SMOKE CONTROL FOR DOORS, SHUTTERS AND OPENABLE WINDOWS
    S.R. CEN ISO TS 24817:2011 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
    ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
    BS EN 15274:2015 General purpose adhesives for structural assembly. Requirements and test methods
    CEN ISO/TS 24817:2011 Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection (ISO/TS 24817:2006)
    BS 7008-1(1994) : AMD 8821 ACQUISITION AND PRESENTATION OF COMPARABLE DATA FOR BASIC PROPERTIES OF PLASTICS - METHOD FOR SINGLE POINT DATA

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
    ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
    ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
    ISO 10724-1:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
    ISO 14125:1998 Fibre-reinforced plastic composites Determination of flexural properties
    ISO 2818:1994 Plastics — Preparation of test specimens by machining
    ISO 178:2010 Plastics Determination of flexural properties
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective