Skip to content
Please enter a keyword to search

  • IPC J STD 004 : B

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    REQUIREMENTS FOR SOLDERING FLUXES

    Available format(s):  Hardcopy

    Superseded date:  10-03-2022

    Language(s): 

    Published date: 

    Publisher:  Institute of Printed Circuits

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 SCOPE AND DESIGNATION
    2 APPLICABLE DOCUMENTS
    3 GENERAL REQUIREMENTS
    4 QUALIFICATIONS AND QUALITY ASSURANCE PROVISIONS
    Appendix A - Example Qualification Test Report
    Appendix B - Notes

    Abstract - (Show below) - (Hide below)

    Describes general requirements for the classification and characterization of fluxes for high quality solder interconnections.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes QQ S 571, MIL F 14256, IPC SF 818, QPL 14256, QPL QQ S 571 & DEFSTAN 34-4/2(1990). Included in IPC C 103 & IPC C 1000. (04/2006) A2004 Edition is available in Japanese Language, See J STD 004 JAPANESE. B2008 Edition Re-Issued in November 2011 & incorporates AMD 1 2011. Also available in Chinese & Russian languages, See J STD 004 CHINESE & J STD 004 RUSSIAN. (11/2012)
    Document Type Standard
    Publisher Institute of Printed Circuits
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    IPC J STD 002 CHINESE : C SOLDERABILITY TESTS FOR COMPONENT LEADS, TERMINATIONS, LUGS, TERMINALS AND WIRES
    MIL-PRF-83504 Revision C:2005 SWITCHES, DUAL IN-LINE PACKAGE (DIP), GENERAL SPECIFICATION FOR
    MIL-DTL-83513 Revision G:2008 CONNECTORS, ELECTRICAL, RECTANGULAR, MICROMINIATURE, POLARIZED SHELL, GENERAL SPECIFICATION FOR
    MIL-C-11272 Revision E:2008 CAPACITORS, FIXED, GLASS DIELECTRIC, GENERAL SPECIFICATION FOR
    IPC AJ 820 : A ASSEMBLY AND JOINING HANDBOOK
    MIL-DTL-83731-16 Revision D:2007 Switches, Toggle, Miniature, Right Angle (Horizontal), PCB Mount, Double Pole, Lever Seal, Flux Seal
    MIL-PRF-914 Revision C:2008 RESISTOR NETWORK, FIXED, FILM, SURFACE MOUNT, NONESTABLISHED RELIABILITY, AND ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
    MIL C 5 : G CAPACITOR, FIXED, MICA DIELECTRIC, GENERAL SPECIFICATION FOR
    MIL C 39019 : C CIRCUIT BREAKERS, MAGNETIC, LOW-POWER, SEALED, TRIP-FREE, GENERAL SPECIFICATION FOR
    MIL-DTL-3607 Revision C:2009 CONNECTORS, COAXIAL, RADIOFREQUENCY, SERIES FOR PULSE, GENERAL SPECIFICATION FOR
    IPC J STD 001 SWEDISH : E REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    IPC A 610 DANISH : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    MIL-DTL-28778 Revision A:2005 TRANSFORMER, POWER, STEPUP, 3 PHASE
    MIL-DTL-12109-21 Revision B:2011 SOLENOID, ELECTRICAL; CLASS 2 (MACHINE GUN) 7.62 MM, 24 VOLT DC, 8 AMP MAX
    MIL-DTL-22641 Revision G:2016 ADAPTERS, COAXIAL TO WAVEGUIDE, GENERAL SPECIFICATION FOR
    MIL P 50884 : E PRINTED WIRING BOARD, FLEXIBLE OR RIGID-FLEX, GENERAL SPECIFICATION FOR
    IPC J STD 001 RUSSIAN : E REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    MIL-DTL-7879 Revision E:2013 ANTENNA AT-141A/ARC
    IPC A 610 SPANISH : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    IPC LDFR0805-CD : 2005 IPC/JEDEC 9TH INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES AUGUST 2005
    IPC WHMA A 620 HUNGARIAN : B REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES
    IPC J STD 005 RUSSIAN : A REQUIREMENTS FOR SOLDERING FLUXES
    IPC J STD 001 TURKISH : E2010 REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    IPC J STD 001 POLISH : E REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    MIL-DTL-13253 Revision E:2007 HANDSETS, GENERAL SPECIFICATION FOR
    IPC A 610 ROMANIAN : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    IPC LDFR1006-CD : 2006 IPC/JEDEC INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES "ROHS COMPLIANCE AND BEYOND"
    MIL-DTL-14072 Revision F:2013 FINISHES FOR GROUND BASED ELECTRONIC EQUIPMENT
    MIL PRF 83513 : D CONNECTORS, ELECTRICAL, RECTANGULAR, MICROMINIATURE, POLARIZED SHELL, GENERAL SPECIFICATION FOR
    IPC WHMA A 620 TURKISH : B2012 AMD 1 2013 REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES
    MIL-DTL-15743 Revision F:2017 SWITCHES, ROTARY, ENCLOSED
    IPC A 610 CZECH : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    IPC TP 1090 : 1996 THE LAYMAN'S GUIDE TO QUALIFYING NEW FLUXES FOR MIL-STD-2000A OR MT-0002
    IPC LDFR0806-CD : 2006 IPC/JEDEC INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES "ROHS COMPLIANCE AND BEYOND"
    IPC LDFR0605-CD : 2005 IPC/SOLDERTEC 3RD INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONICS "TOWARDS IMPLEMENTATION OF THE ROHS DIRECTIVE"
    IPC LDFR1005-CD : 2005 IPC/JEDEC 11TH INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES
    IPC A 610 HINDI : E2010 ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    MIL-DTL-45068 Revision E:2006 LIGHT, DOME, VEHICULAR, 24 VOLT DC
    IPC 9592 : B REQUIREMENTS FOR POWER CONVERSION DEVICES FOR THE COMPUTER AND TELECOMMUNICATIONS INDUSTRIES
    IPC 5702 : 0 GUIDELINES FOR OEMS IN DETERMINING ACCEPTABLE LEVELS OF CLEANLINESS OF UNPOPULATED PRINTED BOARDS
    IPC LDFR1106-CD : 2006 IPC/JEDEC INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES "ROHS COMPLIANCE AND BEYOND"
    IPC A 610 ESTONIAN : E2010 ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    IPC A 610 POLISH : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    IPC WHMA A 620 SPANISH : B REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES
    IPC WHMA A 620 CHINESE : B REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES
    MIL-PRF-39017 Revision G:2006 RESISTOR, FIXED, FILM (INSULATED), NONESTABLISHED RELIABILITY, AND ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
    IPC WHMA A 620 VIETNAMESE : B2012 REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES
    MIL-DTL-32139 Revision B:2017 Connectors, Electrical, Rectangular, Nanominiature, Polarized Shell, General Specification for
    MIL-PRF-39003 Revision N:2016 Capacitor, Fixed, Electrolytic (Solid Electrolyte), Tantalum, Established Reliability, General Specification for
    MIL B 18 : F BATTERIES, NON-RECHARGEABLE, DRY
    IPC A 610 KOREAN : F2014 ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    MIL-DTL-28754-62 Revision A:2016 CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER, CROSSOVER, CONTACT TAILS ON .050 CENTERS
    MIL-STD-2003-5 Revision A:2009 ELECTRIC PLANT INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CONNECTORS)
    MIL-DTL-28748 Revision D:2001 CONNECTOR, PLUG AND RECEPTACLE, RECTANGULAR, RACK AND PANEL SOLDER TYPE AND CRIMP TYPE CONTACTS - GENERAL SPECIFICATION FOR
    MIL-PRF-55681 Revision G:2016 CAPACITOR, CHIP, MULTIPLE LAYER, FIXED, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
    IPC CH 65 : B GUIDELINES FOR CLEANING OF PRINTED BOARDS AND ASSEMBLIES
    IPC LDFR0306-CD : 2006 IPC/JEDEC INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES
    IPC CH 65 CHINESE : B GUIDELINES FOR CLEANING OF PRINTED BOARDS AND ASSEMBLIES
    IPC LDFR1205-CD : 2006 IPC/JEDEC 12TH INTERNATIONAL CONFERENCE ON LEAD FREE ELECTRONIC COMPONENTS AND ASSEMBLIES - DECEMBER 2005
    MIL-DTL-917 Revision F:2014 ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS FOR
    IPC A 610 ITALIAN : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    MIL-DTL-3786 Revision J:2013 SWITCHES, ROTARY (CIRCUIT SELECTOR, LOW-CURRENT CAPACITY), GENERAL SPECIFICATION FOR
    IPC A 610 FRENCH : F ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    MIL-STD-1353 Revision C:2014 ELECTRICAL CONNECTORS, PLUG-IN SOCKETS AND ASSOCIATED HARDWARE, SELECTION AND USE OF
    MIL-DTL-3965 Revision H:2004 CAPACITOR, FIXED ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM, GENERAL SPECIFICATION FOR
    MIL STD 750-2 : A MECHANICAL TEST METHODS FOR SEMICONDUCTOR DEVICES - PART 2: TEST METHODS 2001 THROUGH 2999
    MIL-PRF-49467 Revision C:2005 Capacitor, Fixed, Ceramic, Multilayer, High Voltage (General Purpose), General Specification For
    MIL-DTL-28827 Revision C:2011 SWITCHES, THERMOSTATIC, (VOLATILE LIQUID), HERMETICALLY SEALED, GENERAL SPECIFICATION FOR
    IPC SM 840 : E QUALIFICATION AND PERFORMANCE SPECIFICATION OF PERMANENT SOLDER MASK AND FLEXIBLE COVER MATERIALS
    IPC TR 467 : 0 SUPPORTING DATA AND NUMERICAL EXAMPLES FOR J-STD-001 (CONTROL OF FLUXES)
    MIL PRF 24308 : D CONNECTORS, ELECTRIC, RECTANGULAR, NONENVIRONMENTAL, MINIATURE, POLARIZED SHELL, RACK AND PANEL, GENERAL SPECIFICATION FOR
    IPC HDBK 830 : A GUIDELINES FOR DESIGN, SELECTION AND APPLICATION OF CONFORMAL COATINGS
    IPC J STD 001 HUNGARIAN : E REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    IPC J STD 001 GERMAN : F REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    IPC 9203 : 0 USERS GUIDE TO IPC-9202 AND THE IPC-B-52 STANDARD TEST VEHICLE
    IPC A 610 SWEDISH : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    IPC J STD 075 GERMAN : 0 CLASSIFICATION OF NON-IC ELECTRONIC COMPONENTS FOR ASSEMBLY PROCESSES
    IPC SM 840 CHINESE : E QUALIFICATION AND PERFORMANCE SPECIFICATION OF PERMANENT SOLDER MASK AND FLEXIBLE COVER MATERIALS
    IPC A 610 HUNGARIAN : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    IPC WHMA A 620 POLISH : B REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES
    MIL-DTL-28754-6 Revision D:2014 CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, 40 PIN, STRAIGHT THROUGH
    MIL-PRF-3098 Revision L:2017 CRYSTAL UNITS, QUARTZ, GENERAL SPECIFICATION FOR
    MIL-DTL-1716 Revision J:1997 POLE, TENT, TELESCOPIC, ADJUSTABLE 5 FEET TO 9 FEET, MAGNESIUM
    IPC MI 660 : 1984 INCOMING INSPECTION OF RAW MATERIALS MANUAL
    MIL-DTL-3950 Revision K:2016 Switches, Toggle, Environmentally Sealed, General Specification for
    MIL-DTL-28754-97 Revision A:2015 CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 150 CONTACT, RIGHT ANGLE, CONTACT TAILS ON 0.100 CENTERS
    IPC A 610 CHINESE : F ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    MIL-DTL-9395 Revision K:2016 Switches, Pressure (Absolute, Gage and Differential) General Specification for
    IPC A 610 TURKISH : E2010 ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    IPC LDFR0406-CD : 2006 IPC/SOLDERTEC GLOBAL 4TH INTERNATIONAL ELECTRONICS CONFERENCE AND EXHIBITION "ROHS COMPLIANCE AND BEYOND"
    IPC J STD 006 CHINESE : B-2 REQUIREMENTS FOR ELECTRONIC GRADE SOLDER ALLOYS AND FLUXED AND NON-FLUXED SOLID SOLDERS FOR ELECTRONIC SOLDERING APPLICATIONS
    IPC J STD 001 ROMANIAN : F REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    IPC J STD 005 : A REQUIREMENTS FOR SOLDERING PASTES
    MIL-PRF-27 Revision G:2014 TRANSFORMERS AND INDUCTORS (AUDIO, POWER, AND HIGH-POWER PULSE), GENERAL SPECIFICATION FOR
    MIL STD 11991 : A GENERAL STANDARD FOR PARTS, MATERIALS, AND PROCESSES
    IPC A 610 JAPANESE : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    IPC J STD 005 CHINESE : A REQUIREMENTS FOR SOLDERING PASTES
    IPC J STD 075 CHINESE : - CLASSIFICATION OF NON-IC ELECTRONIC COMPONENTS FOR ASSEMBLY PROCESSES
    MIL-DTL-83731-22 Revision C:2010 SWITCHES, TOGGLE, MINIATURE, LEVER-LOCK, FOUR POLE, LOGIC LOAD TO 5 AMPERES
    MIL DTL 28754/60 : A CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS
    MIL-DTL-16225 Revision C:2010 LOUDSPEAKER, PERMANENT MAGNET, BLASTPROOF AND SUBMERSIBLE, NAVY TYPE 49546()
    IPC J STD 001 DANISH : E REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    MIL-DTL-11996 Revision C:2015 HANDSETS, GENERAL SPECIFICATION FOR
    OO-S-256 Revision K:2012 Sewing Machine, Industrial, General Specification for
    MIL-DTL-83731-15 Revision D:2007 Switches, Toggle, Miniature, Right Angle (Vertical), PCB Mount, Single Pole, Lever Seal, Flux Seal
    IPC A 610 VIETNAMESE : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    MIL-DTL-12606 Revision E:2000 LOUDSPEAKER, PERMANENT MAGNET (UNENCASED, 3-INCH AND 4-INCH DIAMETER CONE, 2-WATT; FUNGUS-, AND IMMERSION-RESISTANT), TYPE LS-445/U, M12606-01, AND M12606-02
    MIL-DTL-12632 Revision E:2016 LOUDSPEAKERS, PERMANENT MAGNET (ENCASED, 2-WATT, FUNGUS-, GUNBLAST-, AND IMMERSION-RESISTANT), GENERAL SPECIFICATION FOR
    MIL-DTL-83731-21 Revision B:2010 SWITCHES, TOGGLE, MINIATURE, LEVER SEAL, PANEL SEAL, FOUR POLE LOGIC LOAD TO 5 AMPERES
    IPC WHMA A 620 ESTONIAN : B2012 AMD 1 2013 REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES
    IPC TP 1115 : 1998 SELECTION AND IMPLEMENTATION STRATEGY FOR A LOW-RESIDUE, NO-CLEAN PROCESS
    IPC WHMA A 620 KOREAN : B2012 AMD 1 2013 REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES
    MIL-DTL-18793 Revision B:2011 ANTENNA AS-333/AP
    MIL-STD-186 Revision F:2002 PROTECTIVE FINISHING SYSTEMS FOR ROCKETS, GUIDED MISSILES, SUPPORT EQUIPMENT AND RELATED MATERIALS
    MIL-STD-981 Revision C:2010 DESIGN, MANUFACTURING AND QUALITY STANDARDS FOR CUSTOM ELECTROMAGNETIC DEVICES FOR SPACE APPLICATIONS
    I.S. EN 3155-039:2007 AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 039: CONTACTS, ELECTRICAL, COAXIAL, SIZE 16, FEMALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD
    MS27144 Revision D:2016 CONNECTOR, PLUG, ELECTRICAL, SOCKET CONTACT, NO. 14 AND 16 AWG, WATERPROOF
    MIL-DTL-32234 Base Document:2007 CONNECTORS, ELECTRICAL, ULTRA HIGH DENSITY, MODULAR, BLADE AND FORK, EIGHT ROW, GENERAL SPECIFICATION FOR
    NASA KSC SPEC E 0031 : 2008 CABLES, ELECTRICAL, SPECIFICATION FOR
    IEC TR 62866:2014 Electrochemical migration in printed wiring boards and assemblies - Mechanisms and testing
    IPC WHMA A 620 DANISH : B REQUIREMENTS AND ACCEPTANCE FOR CABLE AND WIRE HARNESS ASSEMBLIES
    MIL-DTL-83725 Revision E:2017 Relays, Vacuum, General Specification for
    BS EN 61191-2:2017 PRINTED BOARD ASSEMBLIES - PART 2: SECTIONAL SPECIFICATION - REQUIREMENTS FOR SURFACE MOUNT SOLDERED ASSEMBLIES (IEC 61191-2:2017)
    EN 61191-2:2017 Printed board assemblies - Part 2: Sectional specification - Requirements for surface mount soldered assemblies
    IEC 61191-2:2017 Printed board assemblies - Part 2: Sectional specification - Requirements for surface mount soldered assemblies
    MIL-DTL-28754-59 Revision A:2016 CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER CONTACT TAILS ON .100 CENTERS (CERAMIC COMPATIBLE)
    MIL-DTL-5794 Revision C:2006 MICROPHONE UNIT M-6A/UR AND MICROPHONE, CARBON M-51/UR (CARBON NOISE CANCELING)
    IPC J STD 001 CHINESE : F REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    MIL-STD-883 Revision K:2016 TEST METHOD STANDARD - MICROCIRCUITS
    MIL-DTL-28754-10 Revision D:2014 CONNECTORS, ELECTRICAL, MODULAR, CONNECTOR, TYPE 4, 40 PIN, CONTACT TAILS ON 0.050 CENTERS
    I.S. EN 61191-1:2013 PRINTED BOARD ASSEMBLIES - PART 1: GENERIC SPECIFICATION - REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES USING SURFACE MOUNT AND RELATED ASSEMBLY TECHNOLOGIES (IEC 61191-1:2013 (EQV))
    IEC 61191-3:2017 Printed board assemblies - Part 3: Sectional specification - Requirements for through-hole mount soldered assemblies
    NASA MSFC STD 3012 : 2012 ELECTRICAL, ELECTRONIC, AND ELECTROMECHANICAL (EEE) PARTS MANAGEMENT AND CONTROL REQUIREMENTS FOR MSFC SPACE FLIGHT HARDWARE
    BS EN 61191-1:2013 PRINTED BOARD ASSEMBLIES - PART 1: GENERIC SPECIFICATION - REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES USING SURFACE MOUNT AND RELATED ASSEMBLY TECHNOLOGIES
    PD IEC/TR 62866:2014 Electrochemical migration in printed wiring boards and assemblies. Mechanisms and testing
    SAE AS 4461 : 2016 ASSEMBLY AND SOLDERING CRITERIA FOR HIGH QUALITY/HIGH RELIABILITY SOLDERING WIRE AND CABLE TERMINATION IN AEROSPACE VEHICLES
    AWS C3.11M/C3.11:2011 SPECIFICATION FOR TORCH SOLDERING
    IEC 61191-1:2013 Printed board assemblies - Part 1: Generic specification - Requirements for soldered electrical and electronic assemblies using surface mount and related assembly technologies
    MIL-DTL-83502 Revision E:2007 Sockets, Plug-in Electronic Components, Round Style, General Specification for
    NASA STD 8739.3 : 1998 SOLDERED ELECTRICAL CONNECTIONS
    MIL-DTL-83731-13 Revision E:2014 SWITCHES, TOGGLE, MINIATURE, RIGHT ANGLE (VERTICAL), PCB MOUNT, SINGLE POLE, LEVER SEAL, FLUX SEAL
    DSCC 89065 : C GENERAL SPECIFICATION FOR HIGH PERFORMANCE, HIGH DENSITY, TWO PIECE, PRINTED CIRCUIT BOARD CONNECTOR
    EN 3155-040:2007 Aerospace series - Electrical contacts used in elements of connection - Part 040: Contacts, electrical, coaxial, size 12, male, type D, solder, class R - Product standard
    GEIA STD 0006 : 2008 REQUIREMENTS FOR USING ROBOTIC HOT SOLDER DIP TO REPLACE THE FINISH ON ELECTRONIC PIECE PARTS
    EN 61191-4:2017 Printed board assemblies - Part 4: Sectional specification - Requirements for terminal soldered assemblies
    MIL-B-49030 Revision A:2010 BATTERIES, DRY (ALKALINE)
    BS EN 50390:2004 Space product assurance. The manual soldering of high-reliability electrical connections
    IEC TS 62647-23:2013 Process management for avionics - Aerospace and defence electronic systems containing lead-free solder - Part 23: Rework and repair guidance to address the implications of lead-free electronics and mixed assemblies
    IPC J STD 001 SPANISH : F REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    IPC A 610 GERMAN : E ACCEPTABILITY OF ELECTRONIC ASSEMBLIES
    MIL-DTL-15514 Revision G:2016 TELEPHONE EQUIPMENT, SOUND POWERED TELEPHONE HANDSET, HEADSET - CHEST SET, AND HEADSET - CHEST SET, NOISE ATTENUATING
    BS EN 61191-3:2017 Printed board assemblies Sectional specification. Requirements for through-hole mount soldered assemblies
    EN 50390:2004 Space product assurance - The manual soldering of high-reliability electrical connections
    MIL-DTL-55235 Revision A:2003 CONNECTORS, COAXIAL, RADIO FREQUENCY, SERIES TPS, GENERAL SPECIFICATION
    PD IEC/TS 62647-23:2013 Process management for avionics. Aerospace and defence electronic systems containing lead-free solder Rework and repair guidance to address the implications of lead-free electronics and mixed assemblies
    DD IEC PAS 62647-23 : DRAFT AUG 2011 PROCESS MANAGEMENT FOR AVIONICS - AEROSPACE AND DEFENCE ELECTRONIC SYSTEMS CONTAINING LEAD-FREE SOLDER - PART 23: REWORK AND REPAIR GUIDANCE TO ADDRESS THE IMPLICATIONS OF LEAD-FREE ELECTRONICS AND MIXED ASSEMBLIES
    MIL-DTL-28754-47 Revision C:2015 CONNECTORS, ELECTRICAL MODULAR, TYPE 4, CONNECTOR, 100 PIN, RIGHT ANGLE CONTACT TAILS ON .100 CENTERS
    MIL-PRF-32560 Base Document:2016 COIL, RADIO FREQUENCY, SURFACE MOUNT, FIXED ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
    I.S. EN 50390:2004 SPACE PRODUCT ASSURANCE - THE MANUAL SOLDERING OF HIGH-RELIABILITY ELECTRICAL CONNECTIONS
    PREN 3155-039 : 200P1 AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 039: CONTACTS, ELECTRICAL, COAXIAL, SIZE 16, FEMALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD
    IPC J STD 001 FRENCH : F REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    DSCC 03024 : C SHIELDING BEAD, ELECTRONIC, CHIP, FERRITE, HIGH RELIABILITY
    BS EN 61191-4:2017 Printed board assemblies Sectional specification. Requirements for terminal soldered assemblies
    MIL-DTL-28754-101 Revision A:2015 CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 0.6 PITCH, 250 CONTACT, CENTER
    15/30327712 DC : 0 BS EN 61191-1 - PRINTED BOARD ASSEMBLIES - PART 1: GENERIC SPECIFICATION - REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES USING SURFACE MOUNT AND RELATED ASSEMBLY TECHNOLOGIES
    DD IEC PAS 62686-1 : DRAFT JULY 2011 PROCESS MANAGEMENT FOR AVIONICS - AEROSPACE QUALIFIED ELECTRONIC COMPONENTS (AQEC) - PART 1: GENERAL REQUIREMENTS FOR HIGH RELIABILITY INTEGRATED CIRCUITS AND DISCRETE SEMICONDUCTORS
    MIL-DTL-18714 Revision F:2012 PRIMER, ELECTRIC, MARK 45 MOD 1
    11/30255124 DC : 0 BS EN 61191-1 - PRINTED BOARD ASSEMBLIES - PART 1: GENERIC SPECIFICATION - REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES USING SURFACE MOUNT AND RELATED ASSEMBLY TECHNOLOGIES
    I.S. EN 61191-2:2017 PRINTED BOARD ASSEMBLIES - PART 2: SECTIONAL SPECIFICATION - REQUIREMENTS FOR SURFACE MOUNT SOLDERED ASSEMBLIES
    MS27145 Revision C:2003 CONNECTOR, PLUG, ELECTRICAL, NO. 14 AWG DOUBLE CONTACT, WATERPROOF
    PREN 3155-041 : 200P1 AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 041: CONTACTS, ELECTRICAL, COAXIAL, SIZE 12, FEMALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD
    BS EN 3155-040:2007 Aerospace series. Electrical contacts used in elements of connection Contacts, electrical, coaxial, size 12, male, type D, solder, class R. Product standard
    NASA STD 8739.2 : 1999 WORKMANSHIP STANDARD FOR SURFACE MOUNT TECHNOLOGY
    MIL-DTL-28754-14 Revision D:2014 Connectors, Electrical, Modular, Connector, Type IV, 20 Contact, Right Angle (for Die Cast Frame)
    MIL-STD-202-210 Base Document:2015 METHOD 210, RESISTANCE TO SOLDERING HEAT
    BS EN 3155-039:2007 Aerospace series. Electrical contacts used in elements of connection Contacts, electrical, coaxial, size 16, female, type D, solder, class R. Product standard
    13/30295427 DC : 0 BS IEC/PAS 61249-8-5 ED.1 - QUALIFICATION AND PERFORMANCE SPECIFICATION OF PERMANENT SOLDER MASK AND FLEXIBLE COVER MATERIALS
    MIL-STD-750-1 Revision A:2015 Environmental Test Methods for Semiconductor Devices Part 1: Test Methods 1000 Through 1999
    MIL-DTL-83731-14 Revision E:2014 SWITCHES, TOGGLE, MINIATURE, RIGHT ANGLE (VERTICAL), PCB MOUNT, DOUBLE POLE, LEVER SEAL, FLUX SEAL
    IEC PAS 62686-1:2011 Process management for avionics - Aerospace qualified electronic components (AQEC) - Part 1: General requirements for high reliability integrated circuits and discrete semiconductors
    IPC J STD 006 : C REQUIREMENTS FOR ELECTRONIC GRADE SOLDER ALLOYS AND FLUXED AND NON-FLUXED SOLID SOLDERS FOR ELECTRONIC SOLDERING APPLICATIONS
    EN 61191-1:2013 PRINTED BOARD ASSEMBLIES - PART 1: GENERIC SPECIFICATION - REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES USING SURFACE MOUNT AND RELATED ASSEMBLY TECHNOLOGIES (IEC 61191-1:2013)
    MS35644 Revision G:2011 FILLER NECK: FUEL TANK - MILITARY VEHICLES
    MIL-DTL-28754-8 Revision D:2014 CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, 40 CONTACT, RIGHT ANGLE (FOR DIE CAST FRAME)
    MIL-DTL-39024 Revision C:2014 JACK, TIP (TEST POINT, PANEL OR PRINTED WIRING TYPE), GENERAL SPECIFICATION FOR
    MIL-DTL-28754-61 Revision A:2016 CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 100 PIN, CENTER, CROSSOVER, CONTACT TAILS ON .100 CENTERS (CERAMIC COMPATIBLE)
    IEC PAS 61249-8-5:2014 Qualification and performance specification of permanent solder mask and flexible cover materials
    MIL-DTL-13625 Revision G:2017 SWITCHES, PULL; SWITCHES, PUSH; SWITCHES, BEAM SELECTING, HEADLIGHT: ELECTRICAL (28 VOLTS DC MAXIMUM, FOR MILITARY VEHICLES)
    I.S. EN 3155-040:2007 AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 040: CONTACTS, ELECTRICAL, COAXIAL, SIZE 12, MALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD
    EN 61191-3:2017 Printed board assemblies - Part 3: Sectional specification - Requirements for through-hole mount soldered assemblies
    IEC PAS 62647-23:2011 Process management for avionics - Aerospace and defence electronic systems containing lead-free solder - Part 23: Rework and repair guidance to address the implications of lead-free electronics and mixed assemblies
    IEC 61191-4:2017 Printed board assemblies - Part 4: Sectional specification - Requirements for terminal soldered assemblies
    BS EN 3155-041:2007 Aerospace series. Electrical contacts used in elements of connection Contacts, electrical, coaxial, size 12, female, type D, solder, class R. Product standard
    EN 3155-041:2007 Aerospace series - Electrical contacts used in elements of connection - Part 041: Contacts, electrical, coaxial, size 12, female, type D, solder, class R - Product standard
    PREN 3155-040 : 200P1 AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 040: CONTACTS, ELECTRICAL, COAXIAL, SIZE 12, MALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD
    MIL-DTL-28754-11 Revision F:2014 CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, 40 CONTACT, RIGHT ANGLE (FOR SOLID OR DIP FRAME)
    I.S. EN 61191-3:2017 PRINTED BOARD ASSEMBLIES - PART 3: SECTIONAL SPECIFICATION - REQUIREMENTS FOR THROUGH-HOLE MOUNT SOLDERED ASSEMBLIES
    I.S. EN 61191-4:2017 PRINTED BOARD ASSEMBLIES - PART 4: SECTIONAL SPECIFICATION - REQUIREMENTS FOR TERMINAL SOLDERED ASSEMBLIES
    MIL-DTL-21617 Revision B:2012 CONNECTORS, PLUG AND RECEPTACLE, ELECTRICAL, RECTANGULAR, POLARIZED SHELL, MINIATURE TYPE, GENERAL SPECIFICATION FOR
    MIL-DTL-28754-100 Revision A:2015 CONNECTORS, ELECTRICAL, MODULAR, TYPE 4, CONNECTOR, 200 CONTACT, CENTER
    MIL-PRF-31032 Revision C:2016 Printed Circuit Board/Printed Wiring Board, General Specification for
    PD IEC/PAS 61249-8-5:2014 Qualification and performance specification of permanent solder mask and flexible cover materials
    IPC J STD 075 : 0 CLASSIFICATION OF NON-IC ELECTRONIC COMPONENTS FOR ASSEMBLY PROCESSES
    DSCC 99002 : A TRANSFORMER, SWITCHING
    SAE AMS P 81728 : 2015 PLATING, TIN-LEAD (ELECTRODEPOSITED)
    MS90908 Revision C:2011 FILLER TUBE, FUEL TANK - MILITARY VEHICLES
    GEIA HB 0005-3 : 2008 REWORK/REPAIR HANDBOOK TO ADDRESS THE IMPLICATIONS OF LEAD-FREE ELECTRONICS AND MIXED ASSEMBLIES IN AEROSPACE AND HIGH PERFORMANCE ELECTRONIC SYSTEMS
    I.S. EN 3155-041:2007 AEROSPACE SERIES - ELECTRICAL CONTACTS USED IN ELEMENTS OF CONNECTION - PART 041: CONTACTS, ELECTRICAL, COAXIAL, SIZE 12, FEMALE, TYPE D, SOLDER, CLASS R - PRODUCT STANDARD
    EN 3155-039:2007 Aerospace series - Electrical contacts used in elements of connection - Part 039: Contacts, electrical, coaxial, size 16, female, type D, solder, class R - Product standard

    Standards Referencing This Book - (Show below) - (Hide below)

    IPC T 50 : M TERMS AND DEFINITIONS FOR INTERCONNECTING AND PACKAGING ELECTRONIC CIRCUITS
    IPC J STD 001 : F REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES
    ISO/TS 16949:2009 Quality management systems Particular requirements for the application of ISO 9001:2008 for automotive production and relevant service part organizations
    EN 14582:2016 Characterization of waste - Halogen and sulfur content - Oxygen combustion in closed systems and determination methods
    IPC TM 650 : 0 TEST METHODS MANUAL
    IEC 61189-5:2006 Test methods for electrical materials, interconnection structures and assemblies - Part 5: Test methods for printed board assemblies
    IPC J STD 005 : A REQUIREMENTS FOR SOLDERING PASTES
    ANSI/NCSL Z540 1 : 94(R2002) CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS
    ISO 9455-17:2002 Soft soldering fluxes Test methods Part 17: Surface insulation resistance comb test and electrochemical migration test of flux residues
    GR 78 CORE : ISSUE 2 GENERIC REQUIREMENTS FOR THE PHYSICAL DESIGN AND MANUFACTURE OF TELECOMMUNICATIONS PRODUCTS AND EQUIPMENT
    ISO 10012:2003 Measurement management systems — Requirements for measurement processes and measuring equipment
    ISO 9001:2015 Quality management systems — Requirements
    IPC J STD 003 : C SOLDERABILITY TESTS FOR PRINTED BOARDS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective