Skip to content
Please enter a keyword to search

  • UNE-EN 1366-1:2016

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Fire resistance tests for service installations - Part 1: Ventilation ducts

    Available format(s):  Hardcopy, PDF

    Superseded date:  29-09-2021

    Language(s):  Spanish, Castilian, English

    Published date:  28-09-2016

    Publisher:  Asociacion Espanola de Normalizacion

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
          Introduction
    1 Scope
    2 Normative references
    3 Definitions
    4 Test equipment
    5 Test conditions
    6 Test specimen
    7 Installation of test specimen
    8 Conditioning
    9 Application of instrumentation
    10 Test procedure
    11 Performance criteria
    12 Test report
    13 Field of direct application of test results
    Annex A (informative) Informative General Guidance

    Abstract - (Show below) - (Hide below)

    Defines a procedure to determine the fire resistance of horizontal and vertical ventilation ducts under standard fire conditions. For use in conjunction with EN636-1. Excludes fixing of suspension devices to floors or walls, two or three sided ducts, doors of inspection openings, unless included in the duct to be tested, ducts containing fire dampers at points where they pass through fire separations and ducts whose fire resistance is dependent upon the fire resistance performance of a ceiling.

    General Product Information - (Show below) - (Hide below)

    Committee CTN 23
    Development Note Supersedes UNE 23766-1 (1998) (07/2003)
    Document Type Standard
    Publisher Asociacion Espanola de Normalizacion
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 5167-3:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 3: Nozzles and Venturi nozzles
    EN 520:2004+A1:2009 Gypsum plasterboards - Definitions, requirements and test methods
    EN ISO 5167-2:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice plates (ISO 5167-2:2003)
    EN 15882-1:2011+A1:2017 Extended application of results from fire resistance tests for service installations - Part 1: Ducts
    EN 1364-1:1999 Fire resistance tests for non-loadbearing elements - Part 1: Walls
    EN 1057:2006+A1:2010 Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications
    ISO 13943:2017 Fire safety — Vocabulary
    EN 12237:2003 Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts
    ISO 5167-2:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 2: Orifice plates
    EN ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003)
    EN ISO 5167-3:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2003)
    ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
    EN 1366-8:2004 Fire resistance tests for service installations - Part 8: Smoke extraction ducts
    EN 60584-1:2013 Thermocouples - Part 1: EMF specifications and tolerances
    EN ISO 13943:2017 Fire safety - Vocabulary (ISO 13943:2017)
    EN 1363-1:2012 Fire resistance tests - Part 1: General Requirements
    EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
    EN 1363-2:1999 Fire resistance tests - Part 2: Alternative and additional procedures
    IEC 60584-1:2013 Thermocouples - Part 1: EMF specifications and tolerances
    ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective