|
IEC 60243-1:2013
|
Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
|
IEC 60112:2003+AMD1:2009 CSV
|
Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
|
ISO 6603-2:2000
|
Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing |
|
ISO 293:2004
|
Plastics — Compression moulding of test specimens of thermoplastic materials |
|
IEC 60250:1969
|
Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
|
ISO 294-3:2002
|
Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates |
|
ISO 1133-1:2011
|
Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
|
ISO 16770:2004
|
Plastics Determination of environmental stress cracking (ESC) of polyethylene Full-notch creep test (FNCT) |
|
ISO 10350-1:2017
|
Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
|
ISO 17855-1:2014
|
Plastics — Polyethylene (PE) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
|
ISO 8256:2004
|
Plastics — Determination of tensile-impact strength |
|
ISO 11359-2:1999
|
Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
|
ISO 75-2:2013
|
Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
|
ISO 1628-3:2010
|
Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 3: Polyethylenes and polypropylenes |
|
ISO 527-2:2012
|
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
|
ISO 11357-3:2011
|
Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization |
|
ISO 11357-2:2013
|
Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height |
|
IEC 60296:2012 RLV
|
Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
|
ISO 294-4:2001
|
Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Determination of moulding shrinkage |
|
IEC 60093:1980
|
Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
|
IEC 60695-11-10:2013
|
Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
|
ISO 1183-1:2012
|
Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
|
ISO 1183-2:2004
|
Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
|
ISO 1183-3:1999
|
Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method |
|
ISO 179-1:2010
|
Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
|
ISO 62:2008
|
Plastics Determination of water absorption |
|
ISO 294-1:2017
|
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
|
ISO 4589-2:2017
|
Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
|
ISO 2818:1994
|
Plastics — Preparation of test specimens by machining |
|
ISO 899-1:2017
|
Plastics — Determination of creep behaviour — Part 1: Tensile creep |
|
ISO 20753:2008
|
Plastics Test specimens |
|
ISO 178:2010
|
Plastics Determination of flexural properties |
|
ASTM D 638 : 2014 : REDLINE
|
Standard Test Method for Tensile Properties of Plastics |
|
ASTM D 1693 : 2015 : REDLINE
|
Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |