|
ISO 2811-1:2016
|
Paints and varnishes — Determination of density — Part 1: Pycnometer method |
|
ISO/IEC 17025:2005
|
General requirements for the competence of testing and calibration laboratories |
|
ISO 21809-2:2014
|
Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 2: Single layer fusion-bonded epoxy coatings |
|
ISO 8502-3:2017
|
Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method) |
|
ISO 7619-1:2010
|
Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 1: Durometer method (Shore hardness) |
|
ISO 8501-1:2007
|
Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
|
ISO/TS 29001:2010
|
Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations |
|
ISO 3303-1:2012
|
Rubber- or plastics-coated fabrics Determination of bursting strength Part 1: Steel-ball method |
|
SSPC-SP 13 : 1997
|
SURFACE PREPARATION OF CONCRETE |
|
ISO 8503-2:2012
|
Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure |
|
ASTM D 1141 : 1998 : EDT 1
|
Standard Practice for the Preparation of Substitute Ocean Water |
|
ISO 2808:2007
|
Paints and varnishes Determination of film thickness |
|
SSPC-SP 11 : 2012
|
POWER-TOOL CLEANING TO BARE METAL |
|
SSPC-CS 23.00 : 2016
|
SPECIFICATION FOR THE APPLICATION OF THERMAL SPRAY COATINGS (METALLIZING) OF ALUMINUM, ZINC, AND THEIR ALLOYS AND COMPOSITES FOR THE CORROSION PROTECTION OF STEEL |
|
ASTM D 4541 : 2017 : REDLINE
|
Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
|
SSPC-SP 10 : 2015
|
NEAR-WHITE BLAST CLEANING |
|
ISO 188:2011
|
Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
|
ISO 8503-3:2012
|
Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Focusing microscope procedure |
|
ASTM D 2084 : 2017 : REDLINE
|
TEST METHOD FOR RUBBER PROPERTY - VULCANIZATION USING OSCILLATING DISK CURE METER |
|
ASTM D 4285 : 1983 : R2018
|
Standard Test Method for Indicating Oil or Water in Compressed Air |
|
ISO 34-1:2015
|
Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces |
|
ISO 8501-3:2006
|
Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 3: Preparation grades of welds, edges and other areas with surface imperfections |
|
ISO 4591:1992
|
Plastics — Film and sheeting — Determination of average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques (gravimetric thickness) |
|
ISO 4625-1:2004
|
Binders for paints and varnishes Determination of softening point Part 1: Ring-and-ball method |
|
ISO 527-2:2012
|
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
|
ISO 11357-3:2011
|
Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization |
|
ISO 11357-2:2013
|
Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height |
|
ISO 1523:2002
|
Determination of flash point — Closed cup equilibrium method |
|
ISO 1431-1:2012
|
Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing |
|
ISO 4624:2016
|
Paints and varnishes — Pull-off test for adhesion |
|
ISO 3801:1977
|
Textiles — Woven fabrics — Determination of mass per unit length and mass per unit area |
|
AWS C2.25/C2.25M : 2012
|
SPECIFICATION FOR THERMAL SPRAY FEEDSTOCK - WIRE AND RODS |
|
ISO 10474:2013
|
Steel and steel products — Inspection documents |
|
SSPC-SP 6 : 2015
|
COMMERCIAL BLAST CLEANING |
|
ISO 80000-1:2009
|
Quantities and units — Part 1: General |
|
ISO 2178:2016
|
Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method |
|
ISO 62:2008
|
Plastics Determination of water absorption |
|
ISO 11357-6:2008
|
Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
|
ISO 5893:2002
|
Rubber and plastics test equipment Tensile, flexural and compression types (constant rate of traverse) Specification |
|
ISO 3251:2008
|
Paints, varnishes and plastics Determination of non-volatile-matter content |
|
ASTM D 257 : 2014 : REDLINE
|
Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
|
ISO 8502-6:2006
|
Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 6: Extraction of soluble contaminants for analysis The Bresle method |
|
ISO 8503-1:2012
|
Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces |
|
ISO 37:2017
|
Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
|
SSPC-SP 5 : 2015
|
WHITE METAL BLAST CLEANING |
|
ASTM D 695 : 2015 : REDLINE
|
Standard Test Method for Compressive Properties of Rigid Plastics |
|
ISO 8504-2:2000
|
Preparation of steel substrates before application of paints and related products Surface preparation methods Part 2: Abrasive blast-cleaning |
|
ISO 8503-4:2012
|
Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Stylus instrument procedure |
|
ISO 3417:2008
|
Rubber Measurement of vulcanization characteristics with the oscillating disc curemeter |
|
ASTM D 1000 : 2017 : REDLINE
|
Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
|
ISO 11357-1:2016
|
Plastics — Differential scanning calorimetry (DSC) — Part 1: General principles |
|
ISO 527-3:1995
|
Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
|
ISO 8504-3:1993
|
Preparation of steel substrates before application of paints and related products Surface preparation methods Part 3: Hand- and power-tool cleaning |
|
ISO 8503-5:2017
|
Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 5: Replica tape method for the determination of the surface profile |
|
ISO 527-1:2012
|
Plastics Determination of tensile properties Part 1: General principles |
|
ISO 13623:2017
|
Petroleum and natural gas industries — Pipeline transportation systems |
|
ISO 4593:1993
|
Plastics Film and sheeting Determination of thickness by mechanical scanning |
|
ISO 868:2003
|
Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
|
ISO 1817:2015
|
Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
|
ISO 2781:2008
|
Rubber, vulcanized or thermoplastic Determination of density |