UNI EN 10025-6 : 2009

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 6: TECHNICAL DELIVERY CONDITIONS FOR FLAT PRODUCTS OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED CONDITION

Available format(s):

Superseded date: 09-05-2022

Language(s):

Published date: 01-01-2009

Publisher: Ente Nazionale Italiano di Unificazione (UNI)

Table of Contents - (Show below) - (Hide below)

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification and designation
5 Information to be supplied by the purchaser
6 Manufacturing process
7 Requirements
8 Inspection
9 Preparation of samples and test pieces
10 Test methods
11 Marking, labelling, packaging
12 Complaints
13 Options
Annex A (informative) - List of corresponding former
        designations
Annex B (informative) - List of national standards which
        correspond with ECSC IC 2 referenced
Annex C (informative) - Minimum recommended inside
        bend radii for flanging
Bibliography

Abstract - (Show below) - (Hide below)

Describes requirements for flat products of high yield strength alloy special steels.

General Product Information - (Show below) - (Hide below)

Development Note	Supersedes UNI EN 10137-1 and UNI EN 10137-2. (04/2005)
Document Type	Standard
ISBN
Pages
Published
Publisher	Ente Nazionale Italiano di Unificazione (UNI)
Status	Superseded
Superseded By	UNI EN 10025-6:2019
Supersedes	UNI EN 10025-6 : 2005 UNI EN 10137-1 : 1997

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
UNE-EN 10025-6:2007	Identical
DIN EN 10025-6:2011-04 (Draft)	Identical
NEN EN 10025-6 : 2004 + A1 2009	Identical
ONORM EN 10025-6 : 2010	Identical
NS EN 10025-6 : 2004 + A1 2009	Identical
BS EN 10025-6 : 2004	Identical
SN EN 10025-6 : 2005 + A1 2009	Identical
EN 10025-6:2004+A1:2009	Identical
I.S. EN 10025-6:2004	Identical
NF EN 10025-6 : 2005 + A1 2009	Identical
NBN EN 10025-6 : 2004 + A1 2009	Identical
DIN EN 10025-6:2009-08	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

UNI 10372 : 2013	DISCONTINUOUSLY LAID ROOF COVERINGS - CRITERIA FOR DESIGN, EXECUTION AND MAINTENANCE OF ROOFING MADE OF METAL SHEETS

Standards Referencing This Book - (Show below) - (Hide below)

EN 10162:2003	Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances
EN 10048:1996	Hot rolled narrow steel strip - Tolerances on dimensions and shape
EN 10051:2010	Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
EN 10027-2:2015	DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM
EN 10029:2010	Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
EN 10164:2004	Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
EN ISO 1461:2009	Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009)
ISO 1461:2009	Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
EN ISO 2566-1:1999	Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984)
EN 10025-1:2004	Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 1011-2:2001/A1:2003	WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 2: ARC WELDING OF FERRITIC STEELS
EN 10163-2:2004	Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats
EN 10163-1:2004/AC:2007	DELIVERY REQUIREMENTS FOR SURFACE CONDITION OF HOT-ROLLED STEEL PLATES, WIDE FLATS AND SECTIONS - PART 1: GENERAL REQUIREMENTS
ISO 14713:1999	Protection against corrosion of iron and steel in structures Zinc and aluminium coatings Guidelines
ISO 2566-1:1984	Steel Conversion of elongation values Part 1: Carbon and low alloy steels
EN 10027-1:2016	Designation systems for steels - Part 1: Steel names
EN 10020:2000	Definition and classification of grades of steel
CEN/TR 10347:2006	Guidance for forming of structural steels in processing
EN 10160:1999	Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method)
EN ISO 14713 : 1999	PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - ZINC AND ALUMINIUM COATINGS - GUIDELINES

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart