• There are no items in your cart

UNI EN 13617-1 : 2012

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS

Superseded date

30-03-2022

Published date

01-01-2012

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Tests
7 Information for use
Annex A (normative) - Classification of vapour barriers
Annex B (informative) - Information on explosion protected
        equipment
Annex C (informative) - Environmental aspects
Annex ZA (informative) - Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 94/9/EC
Annex ZB (informative) - Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 2006/42/EC
Bibliography

Pertains to metering pumps, dispensers and remote pumping units to be installed at petrol filling stations, designed to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200l min-1, and intended for use and storage at ambient temperatures between -20 degrees C and +40 degrees C.

DocumentType
Standard
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
SupersededBy
Supersedes

IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
EN 1127-1:2011 Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology
IEC 60079-1:2014 RLV Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
CEN/TS 15293:2011 Automotive fuels - Ethanol (E85) automotive fuel - Requirements and test methods
EN 60079-26:2015 Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga
EN 60079-1:2014 Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
EN 60079-10-1:2015 Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres
ISO 9329-3:1997 Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 3: Unalloyed and alloyed steels with specified low temperature properties
EN 228:2012+A1:2017 Automotive fuels - Unleaded petrol - Requirements and test methods
ISO 1825:2010 Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling Specification
IEC 60730-2-10:2006 Automatic electrical controls for household and similar use - Part 2-10: Particular requirements for motor-starting relays
EN 1057:2006+A1:2010 Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications
EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
EN 13617-2:2012 Petrol filling stations - Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers
EN 60079-15:2010 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
EN 13483:2013 Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
EN 13463-1:2009 Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
IEC 60079-18:2014 RLV Explosive atmospheres - Part 18: Equipment protection by encapsulation “m”
EN 60950-1:2006/A2:2013 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
EN ISO 1182:2010 Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010)
EN 13617-3:2012 Petrol filling stations - Part 3: Safety requirements for construction and performance of shear valves
ISO 9329-1:1989 Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 1: Unalloyed steels with specified room temperature properties
IEC 60079-10-1:2015 Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres
EN 60079-6:2015 Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o"
ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction
ISO 9329-4:1997 Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 4: Austenitic stainless steels
IEC 60079-5:2015 RLV Explosive atmospheres - Part 5: Equipment protection by powder filling "q"
EN 14125:2013 Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
ISO 1182:2010 Reaction to fire tests for products Non-combustibility test
HD 22-4 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING CROSS-LINKED INSULATION - PART 4: CORDS AND FLEXIBLE CABLES
EN 60947-3:2009/A2:2015 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 3: SWITCHES, DISCONNECTORS, SWITCH-DISCONNECTORS AND FUSE-COMBINATION UNITS (IEC 60947-3:2008/A2:2015)
EN 60079-11:2012 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-11:2011 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
ISO 9329-2:1997 Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 2: Unalloyed and alloyed steels with specified elevated temperature properties
ISO 11925-3:1997 Reaction to fire tests — Ignitability of building products subjected to direct impingement of flame — Part 3: Multi-source test
EN 60079-25:2010/AC:2013 EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS (IEC 60079-25:2010)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
HD 21 PT13 : S1 AMD 1 2001 POLYVINYL CHLORIDE INSULATED CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V - OIL RESISTANT PVC SHEATHED CABLES WITH TWO OR MORE CONDUCTORS
IEC 60079-25:2010 Explosive atmospheres - Part 25: Intrinsically safe electrical systems
IEC 60079-6:2015 Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o"
IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
ISO 16852:2016 Flame arresters — Performance requirements, test methods and limits for use
IEC 60079-14:2013 Explosive atmospheres - Part 14: Electrical installations design, selection and erection
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
EN 60079-14:2014/AC:2016 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016)
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
EN 60079-5:2015 Explosive atmospheres - Part 5: Equipment protection by powder filling "q"
EN 13012:2012 Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers
IEC 60947-3:2008+AMD1:2012+AMD2:2015 CSV Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units
EN 1360:2013 Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
EN 60730-2-10:2007 Automatic electrical controls for household and similar use - Part 2-10: Particular requirements for motor-starting relays
IEC 60079-15:2010 Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
IEC 60079-26:2014 RLV Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga
EN ISO 16852:2016 Flame arresters - Performance requirements, test methods and limits for use (ISO 16852:2016)
CLC/TR 50404:2003 Electrostatics - Code of practice for the avoidance of hazards due to static electricity
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
EN 60079-2:2014/AC:2015 EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014)

Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.