UNI EN 16304 : 2013

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

AUTOMATIC VENT VALVES FOR GAS BURNERS AND GAS BURNING APPLIANCES

Available format(s):

Superseded date: 07-12-2022

Language(s):

Published date: 11-04-2013

Publisher: Ente Nazionale Italiano di Unificazione (UNI)

Table of Contents - (Show below) - (Hide below)

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Units of measurement and test conditions
6 Construction requirements
7 Performance
8 EMC/Electrical requirements
9 Marking, installation and operating instructions
Annex A (informative) - Gas connections in common
        use in the various countries
Annex B (informative) - Leak-tightness test - volumetric
        method
Annex C (informative) - Leak-tightness test - pressure
        loss method
Annex D (normative) - Conversion of pressure loss into
        leakage rate
Annex E (normative) - Electrical/electronic component
        fault modes
Annex F (normative) - Additional requirements for safety
        accessories and pressure accessories as defined
        in EU Directive 97/23/EC
Annex G (normative) - Materials for pressurised parts
Annex H (informative) - Additional materials for
        pressurised parts
Annex I (normative) - Requirements for controls used
        in DC supplied gas burners and gas burning
        appliances
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 2009/142/EC
         relating to appliances burning gaseous fuels
Bibliography

Abstract - (Show below) - (Hide below)

This European Standard specifies the safety, construction and performance requirements for automatic vent vales for use with gas burners, gas appliances and similar use, hereafter referred to as “valves”.

General Product Information - (Show below) - (Hide below)

Committee	CT 114
Document Type	Standard
ISBN
Pages
Published
Publisher	Ente Nazionale Italiano di Unificazione (UNI)
Status	Superseded
Superseded By	UNI EN 16304:2022

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
EN 16304:2013	Identical

Standards Referencing This Book - (Show below) - (Hide below)

EN 13906-1:2013	Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs
EN 175301-803:2006	Detail Specification: Rectangular connectors - Flat contacts, 0,8 mm thickness, locking screw not detachable
EN 13906-2:2013	Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs
EN 437:2003+A1:2009	Test gases - Test pressures - Appliance categories
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	Degrees of protection provided by enclosures (IP Code)
IEC 61058-1:2016	Switches for appliances - Part 1: General requirements
EN 13611:2015/AC:2016	SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
EN 61058-1:2002/A2:2008	SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS
EN 60529:1991/AC:2016-12	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 60730-1:2016	Automatic electrical controls - Part 1: General requirements
IEC 60730-1:2013+AMD1:2015 CSV	Automatic electrical controls - Part 1: General requirements

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart