UNI EN ISO 15874-5 : 2013

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM

Available format(s):

Superseded date: 01-09-2022

Language(s):

Published date: 31-12-2012

Publisher: Ente Nazionale Italiano di Unificazione (UNI)

Table of Contents - (Show below) - (Hide below)

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated
terms
4 Fitness for purpose of the joints and the
piping system
Bibliography

Abstract - (Show below) - (Hide below)

Describes the characteristics of the fitness for purpose of polypropylene (PP) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application.

General Product Information - (Show below) - (Hide below)

Development Note	Supersedes UNI 8321 and UNI 8531. (08/2005)
Document Type	Standard
ISBN
Pages
Published
Publisher	Ente Nazionale Italiano di Unificazione (UNI)
Status	Superseded
Superseded By	UNI EN ISO 15874-5:2018
Supersedes	UNI 8531 : 1983 UNI 8321 : 1982 UNI EN ISO 15874-5 : 2005

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
ONORM EN ISO 15874-5 : 2013	Identical
ISO 15874-5:2013	Identical
NF EN ISO 15874-5 : 2013	Identical
NBN EN ISO 15874-5 : 2013	Identical
NEN EN ISO 15874-5 : 2013	Identical
NS EN ISO 15874-5 : 2013	Identical
I.S. EN ISO 15874-5:2013	Identical
SN EN ISO 15874-5:2013	Identical
UNE-EN ISO 15874-5:2013	Identical
BS EN ISO 15874-5 : 2013	Identical
EN ISO 15874-5:2013	Identical
DIN EN ISO 15874-5:2013-06	Identical
DIN EN ISO 15874-5:2004-03	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

UNI 11397 : 2011	WELDING - WELDING OF PLASTICS - WELDING OF POLYPROPYLENE COMPONENTS FOR PRESSURE FLUIDS TRANSMISSION - BUTT WELDING
UNI 11318 : 2009	WELDING - WELDING OF PLASTICS - WELDING OF POLYPROPYLENE COMPONENTS FOR PRESSURE FLUIDS TRANSMISSION - SOCKET WELDING

Standards Referencing This Book - (Show below) - (Hide below)

ISO 19892:2011	Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of joints to pressure cycling
ISO 1167-2:2006	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
ISO 15874-1:2013	Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General
ISO 1167-4:2007	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
ISO 19893:2011	Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of mounted assemblies to temperature cycling
ISO 15874-2:2013	Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 2: Pipes
EN 713:1993	Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending
ISO 1167-3:2007	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components
CEN/TR 12108:2012	Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption
EN 12294:1999	Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum
ISO/TS 15874-7:2003	Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity
EN 712:1993	Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force
ISO 1167-1:2006	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart