Skip to content
Please enter a keyword to search

  • UNI EN ISO 179-1 : 2010

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 1: NON-INSTRUMENTED IMPACT TEST

    Available format(s): 

    Superseded date:  03-08-2023

    Language(s): 

    Published date:  09-09-2010

    Publisher:  Ente Nazionale Italiano di Unificazione (UNI)

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Principle
    5 Apparatus
    6 Test specimens
    7 Procedure
    8 Calculation and expression of results
    9 Precision
    10 Test report
    Annex A (informative) - Additional methods for investigating
       the influence of surface effects
    Annex B (informative) - Precision data
    Annex C (informative) - Determining the notch tip radius using
       a CCD microscope
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes a method for determining the Charpy impact strength of plastics under defined conditions. Defines a number of different types of specimen and test configurations. Also specifies different test parameters according to the type of material, the type of test specimen and the type of notch.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes UNI EN ISO 179. (10/2002)
    Document Type Standard
    Publisher Ente Nazionale Italiano di Unificazione (UNI)
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    UNI 10667-2 : 2010 PLASTIC RAW-SECONDARY MATERIALS - POLYETHYLENE FOR GENERAL PURPOSES FROM THE RECYCLING OF INDUSTRIAL RESIDUES AND/OR FROM PRE AND/OR POST CONSUMER MATERIALS - PART 2: REQUIREMENTS AND TEST METHODS
    UNI 11401 : 2011 GUIDELINE FOR THERMAL BREAK PROFILES
    UNI 10667-3 : 2011 PLASTIC RAW-SECONDARY MATERIALS - POLYPROPYLENE FOR GENERAL PURPOSES FROM THE RECYCLING OF INDUSTRIAL RESIDUES AND/OR FROM PRE AND/OR POST CONSUMER MATERIALS - PART 3: REQUIREMENTS AND TEST METHODS

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
    ISO 3167:2014 Plastics Multipurpose test specimens
    ISO 294-3:2002 Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates
    ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
    ISO 10724-1:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
    ISO 2602:1980 Statistical interpretation of test results Estimation of the mean Confidence interval
    ISO 180:2000 Plastics Determination of Izod impact strength
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
    ISO 2818:1994 Plastics — Preparation of test specimens by machining
    ISO 1268-11:2005 Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates
    ISO 13802:2015 Plastics — Verification of pendulum impact-testing machines — Charpy, Izod and tensile impact-testing
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective