Skip to content
Please enter a keyword to search

  • PREN 2002-02 : 200P3

    View superseded by
    Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
    View superseded by

    AEROSPACE SERIES - METALLIC MATERIALS - TEST METHODS - PART 2: TENSILE TESTING AT ELEVATED TEMPERATURE

    Available format(s):  Hardcopy, PDF

    Withdrawn date:  06-12-2023

    Language(s):  English

    Published date: 

    Publisher:  Aerospace & Defence Industries Association of Europe

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    0 Introduction
    1 Scope
    2 Normative references
    3 Definitions
    4 Health and safety
    5 Principle
    6 Testing requirements
    7 Test report
    Annex A (normative) Types of test piece to be used for sheet
                        and strip with thickness less than 8 mm
    Annex B (normative) Types of non-machined test piece to be used
                        in the case of bar, section and wire with a
                        diameter or thickness less than or equal to
                        8 mm
    Annex C (normative) Types of machined test piece to be used in
                        the case of bar, section, plate and wire
                        with diameter or thickness greater than 8 mm
                        and for forgings and castings
    Annex D (normative) Types of test piece to be used in the case
                        of tubes

    Abstract - (Show below) - (Hide below)

    Specifies the requirements for the tensile testing of metallic materials at elevated temperature for aerospace applications.

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee C5
    Document Type Draft
    Product Note Superseded by EN 2002-002:2005
    Publisher Aerospace & Defence Industries Association of Europe
    Status Withdrawn
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    01/716044 DC : 0 EN 4800-6 - AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 6: PRE-PRODUCTION AND PRODUCTION FORGINGS
    PREN 3225-4 : 200P1 AEROSPACE SERIES - HEAT RESISTING ALLOYS PRODUCED FROM ATOMIZED POWDER - POWDER COMPACTED FORGING STOCK AND PARTS - TECHNICAL SPECIFICATION - PART 4 - PRE-PRODUCTION AND PRODUCTION PARTS
    BS EN 2858-3:1994 Titanium and titanium alloys. Forging stock and forgings. Technical specifications Pre-production and production forgings
    DIN EN 2103-2:1991-11 AEROSPACE SERIES - AEROSPACE SERIES - STEEL, NICKEL BASE AND COBATT BASE ALLOY REMELTING STOCK AND CASTINGS - TECHNICAL SPECIFICATION - PART 2 - REMELTING STOCK
    EN 2103-3 : 1991 AEROSPACE SERIES - STEEL, NICKEL BASE AND COBALT BASE ALLOY REMELTING STOCK AND CASTINGS - TECHNICAL SPECIFICATIONS - PART 3: PRE-PRODUCTION AND PRODUCTION CASTINGS
    PREN 4400-2 : 200P1 AEROSPACE SERIES - ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 2: SHEET AND STRIP
    PREN 2002-23 : 200P1 AEROSPACE SERIES - TEST METHODS FOR METALLIC MATERIALS - PART 23 - SHARP-NOTCH TENSION TESTING
    BS EN 2858-2:1994 Titanium and titanium alloys. Forging stock and forgings. Technical specification. Forging stock
    EN 2103-2 : 1991 AEROSPACE SERIES - STEEL, NICKEL BASE AND COBALT BASE ALLOY REMELTING STOCK AND CASTINGS - TECHNICAL SPECIFICATION - PART 2: REMELTING STOCK
    PREN 3225-3 : 200P1 AEROSPACE SERIES - HEAT RESISTING ALLOYS PRODUCED FROM ATOMIZED POWDER - POWDER COMPACTED FORGING STOCK AND PARTS - TECHNICAL SPECIFICATION - PART 3 - HOT COMPACTED FORGING STOCK

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 60584-2:1993 Thermocouples - Part 2: Tolerances
    PREN 4259 : 200P1 AEROSPACE SERIES - METALLIC MATERIALS - DEFINITION OF GENERAL TERMS
    EN ISO 9513:2012/AC:2013 Metallic materials - Calibration of extensometer systems used in uniaxial testing - Technical Corrigendum 1 (ISO 9513:2012/Cor 1:2013)
    EN 10002-4 : 1994 METALLIC MATERIALS - TENSILE TEST - VERIFICATION OF EXTENSOMETERS USED IN UNIAXIAL TESTING
    EN 4258:1998 Aerospace series - Metallic materials - General organization of standardization - Links between types of EN standards and their use
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective