Skip to content
Please enter a keyword to search

  • BS QC 960000:1992

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Generic specification

    Available format(s):  Hardcopy, PDF

    Superseded date:  28-02-2010

    Language(s):  English

    Published date:  15-10-1992

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Committees responsible
    National foreword
    Introduction
    Section 1. Scope and object
    1.1 Scope
    1.2 Object
    Section 2. General
    2.1 Related publications
    2.2 Units and symbols
    2.3 Terminology
    2.4 Preferred values
    2.5 Marking
    Section 3. Quality assessment procedures
    3.1 Qualification approval/Quality assessment systems
    3.2 Primary stage of manufacture
    3.3 Structurally similar switches
    3.4 Qualification approval procedures
    3.5 Quality conformance inspection
    3.6 Alternative test methods
    3.7 Unchecked parameters
    Section 4. Test and measurement procedures
    4.1 General
    4.2 Standard atmospheric conditions
    4.3 General examination
    4.4 Resistance measurements
    4.5 Voltage stress
    4.6 Temperature rise
    4.7 Dynamic stress
    4.8 Mechanical strength
    4.9 Mechanical endurance
    4.10 Electrical endurance
    4.11 Overload
    4.12 Environmental
    4.13 Soldering
    4.14 Panel seal
    4.15 Enclosure seal
    4.16 Fluid resistance
    4.17 Fire hazard
    4.18 Capacitance
    4.19 Illumination
    Figures
    1. Contact bounce test circuit
    2. Typical trace of contact bounce
    3. Application of forces and torques for test 4.8.1
    4. Submersion seal test enclosure

    Abstract - (Show below) - (Hide below)

    Establishes a uniform quality assessment system and provides consistency by specifying terminology, symbols, test methods and other necessary information.

    General Product Information - (Show below) - (Hide below)

    Committee EPL/48
    Development Note Supersedes 84/20971 DC (08/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS QC 960401:1992 Specification for harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical switches for use in electronic equipment. Blank detail specification for pushbutton switches
    BS QC 960100:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for rotary switches
    BS QC 960200:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for lever (toggle) switches
    BS QC 960400:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for pushbutton switches
    BS QC 960301:1992 Specification for harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical switches for use in electronic equipment. Blank detail specification for sensitive switches
    BS QC 960201:1992 Specification for harmonized system of quality assessment for electronic components. Blank detail specification: electromechanical switches for use in electronic equipment. Blank detail specification for lever (toggle) switches
    BS QC 960300:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for sensitive switches
    BS QC 960500:1992 Harmonized system of quality assessment for electronic components. Electromechanical switches for use in electronic equipment. Sectional specification for in-line package switches

    Standards Referencing This Book - (Show below) - (Hide below)

    BS 5772-8:1985 Specification for electromechanical components for electronic equipment: basic testing procedures and measuring methods Connector tests (mechanical) and mechanical tests on contacts and terminations
    BS 4500-1.1(1990) : AMD 7630 ISO LIMITS AND FITS - GENERAL, TOLERANCES AND DEVIATIONS - SPECIFICATION FOR BASES OF TOLERANCES, DEVIATIONS AND FITS
    BS 5772-4:1979 Specification for electromechanical components for electronic equipment: basic testing procedures and measuring methods Dynamic stress tests
    ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
    BS 6001-1:1991 Sampling procedures for inspection by attributes Specification for sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection
    IEC 60512-7:1993 Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 7: Mechanical operating tests and sealing tests
    BS 2011-2.1XA(1981) : 1981 AMD 7553 ENVIRONMENTAL TESTING - TESTS - TEST XA AND GUIDANCE - IMMERSION IN CLEANING SOLVENTS
    BS 4727-1:GRP13(1991) : 1991 GLOSSARY OF ELECTROTECHNICAL, POWER, TELECOMMUNICATION, ELECTRONICS, LIGHTING AND COLOUR TERMS - TERMS COMMON TO POWER, TELECOMMUNICATIONS AND ELECTRONICS - ELECTROMECHANICAL COMPONENTS FOR ELECTRONIC EQUIPMENT
    BS 4727-2:GRP06(1985) : 1985 GLOSSARY OF ELECTROTECHNICAL POWER TELECOMMUNICATION ELECTRONICS LIGHTING AND COLOUR TERMS - TERMS PARTICULAR TO POWER ENGINEERING - SWITCHGEAR & CONTROLGEAR TERMINOLOGY INCLUDING FUSE TERMINOLOGY
    BS 2011-2.1Z/AD:1977 Environmental testing. Tests Tests Z/AD. Composite temperature/humidity cyclic test
    IEC 60068-2-38:2009 Environmental testing - Part 2-38: Tests - Test Z/AD: Composite temperature/humidity cyclic test
    BS 6334:1983 Methods of test for the determination of the flammability of solid electrical insulating materials when exposed to an igniting source
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    BS QC 001002:1991 Rules of procedure of the IEC quality assessment system for electronic components (IECQ)
    BS 5555:1981 Specification for SI units and recommendations for the use of their multiples and of certain other units
    BS 5772-3:1979 Specification for electromechanical components for electronic equipment: basic testing procedures and measuring methods Current-carrying capacity tests
    PD 6499:1981 Guide to insulation co-ordination within low-voltage systems including clearances and creepage distances for equipment
    BS 2011-2.1T:1981 Environmental testing. Tests Test T. Soldering
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective