MIL-STD-35-109 Base Document:1976

1 INTRODUCTION
  1.1 Scope
  1.2 Purpose
  1.3 Format
  1.4 Military Specification, Exception Title Index
       1.4.1 Title
       1.4.2 Index
2 APPLICABLE DOCUMENTS
3 DEFINITIONS
4 GENERAL DESCRIPTION OF AEDS
5 DETAILED DESCRIPTION OF AEDS
  5.1 Introduction
  5.2 Specification Requirement Sheet (SRS)
  5.3 Specification Requirements
  5.4 Code 1006 Requirement and Test methods
  5.5 Approved Item Code
  5.6 Dimensions and Figures
  5.7 Applicable Documents
  5.8 Tabulation
  5.9 Design and Construction
       5.9.1 Indicator Scale Range
       5.9.2 Indicator Sub Scale Range
       5.9.3 Port Configuration
       5.9.4 Minimum Zero Adjust From Initial Point
       5.9.5 Hermetic Seal
       5.9.6 Case
       5.9.7 Pointer
       5.9.8 Cover Glass
       5.9.9 Parallax
       5.9.10 Bearings
       5.9.11 Lubrication
       5.9.12 Filling Media
       5.9.13 Electrical Receptacle
       5.9.14 Overload Protection
       5.9.15 Maximum Weight
       5.9.16 Dial Marking
       5.9.17 Indicator Input
       5.9.18 Indicator Power
       5.9.19 Lighting Circuit Voltage
  5.10 Acceleration
  5.11 Cold Junction Compensator Lag
  5.12 Current, Resistance Bulb
  5.13 Damping
  5.14 DC Resistance
  5.15 Dead Spot
  5.16 Dielectric Withstanding Voltage at Reduced
       Barometric Pressure
  5.18 Dielectric Withstanding Voltage at Sea Level
  5.19 Dust
  5.20 Effect of Lead Length
  5.21 Electromagnetic Interference
  5.22 Endurance
  5.22 Error, Friction
  5.23 Error, Pointer Zero Position
  5.24 Error, Position
  5.25 Error, Scale
  5.26 Fogging
  5.27 Frequency Cycling
  5.28 Fungus
  5.29 Helium Test
  5.30 Humidity
  5.31 Hysteresis
  5.32 Immersion
  5.33 Indication, Power Off
  5.34 Insulation Resistance
  5.35 Leakage, Diaphragm Capsule
  5.36 Life, Lamp
  5.37 Lighting
  5.38 Low Liquid Level arming Circuit
  5.39 Magnetic Effect
  5.40 Mounting Lugs
  5.41 Open and Short Circuit
  5.42 Operation, Reduced Voltage
  5 43 Overpressure
  5.44 Overspeed and Reverse
  5.45 Power Consumption/Indicator Current
  5.46 Press To Test Circuit
  5.47 Rain
  5.48 Reliability Screening (Burn-In, Aging, Conditioning,
       Stabilization, Load Overload)
  5.49 Resistance to Soldering Heat
  5.50 Response
  5.51 Salt Fog
  5.52 Seal
  5.53 Sensitivity
  5.54 Shock
  5.55 Solderability
  5.56 Starting And Warm up, Low Temperature
  5.57 Starting, Room Temperature
  5.58 Surge, Voltage
  5.59 Temperature - Altitude
  5.60 Temperature, High
  5.61 Temperature, Low
  5.62 Temperature Rise, Indicator
  5.63 Terminal, Strength
  5.64 Thermal Shock
  5.65 Unit Torque Gradient
  5.66 Variation, Voltage and Frequency
  5.67 Vibration
  5.68 Vibration, High Frequency
  5.69 Zero, Electrical
  5.70 Zero Error At Low Temperature
  5.71 Zero Error During Temperature Change

Describes detailed requirements of Indicators, Pointer.