Skip to content
Please enter a keyword to search

  • SAE AMS 4027 : 2014

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    ALUMINUM ALLOY, SHEET AND PLATE, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061; -T6 SHEET, -T651 PLATE), SOLUTION AND PRECIPITATION HEAT TREATED

    Available format(s):  Hardcopy, PDF

    Superseded date:  26-05-2022

    Language(s):  English

    Published date:  16-05-2014

    Publisher:  SAE International

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. APPLICABLE DOCUMENTS
    3. TECHNICAL REQUIREMENTS
    4. QUALITY ASSURANCE PROVISIONS
    5. PREPARATION FOR DELIVERY
    6. ACKNOWLEDGMENT
    7. REJECTIONS
    8. NOTES

    Abstract - (Show below) - (Hide below)

    Specifies an aluminum alloy in the form of sheet and plate.

    General Product Information - (Show below) - (Hide below)

    Committee AMS-D
    Development Note Supersedes SAE AMS QQ A 250/11. (07/2008)
    Document Type Revision
    Publisher SAE International
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    SAE AMS 2477 : 2010 CONVERSION COATING FOR ALUMINUM ALLOYS LOW ELECTRICAL RESISTANCE COATING
    MIL-DTL-22992 Revision H:2015 Connectors, Plugsand Receptacles, Electrical, Waterproof, Quick Disconnect, Heavy Duty Type, General Specification for
    MIL-DTL-83513 Revision G:2008 Connectors, Electrical, Rectangular, Microminiature, Polarized Shell, General Specification for
    MIL-DTL-32139 Revision B:2017 Connectors, Electrical, Rectangular, Nanominiature, Polarized Shell, General Specification for
    MIL-DTL-28748-17 Revision B:2016 CONNECTORS, ELECTRICAL, RECTANGULAR, RACK AND PANEL, HARDWARE FOR
    17/30334746 DC : 0 BS EN 62945 - RADIATION PROTECTION INSTRUMENTATION - MEASURING THE IMAGING PERFORMANCE OF X-RAY COMPUTED TOMOGRAPHY (CT) SECURITY-SCREENING SYSTEMS
    MIL-HDBK-510 Revision A:2014 AEROSPACE FUELS CERTIFICATION
    MIL-DTL-28754 Revision E:2016 Connectors, Electrical, Modular, and Component Parts General Specification for
    MIL-HDBK-510-1 Revision A:2010 AEROSPACE FUELS CERTIFICATION
    SAE AMS 2437 : 2012 COATING, PLASMA SPRAY DEPOSITION
    SAE AMS 3242 : 2011 CHLOROPRENE (CR) RUBBER, WEATHER RESISTANT, 75-85
    SAE AS 27194C : 2014(S2018) SEAL, BONDED, ALUMINUM ALLOY 6061-T6, AMS4027, MOLD IN GROOVE, NBR RUBBER, AMS-P-5315
    SAE AMS 3241 : 2011 CHLOROPRENE (CR) RUBBER, WEATHER RESISTANT, 55-65
    SAE AMS 3240 : 2011 CHLOROPRENE (CR) RUBBER, WEATHER RESISTANT, 35-45
    MIL-DTL-5541 Revision F:2006 Chemical Conversion Coatings on Aluminum and Aluminum Alloys
    MS18193 Revision F:2011 Shield, Electrical Connectors for 66 and 104 Contact Connectors
    SAE AS 27195 : 2014 SEAL, BONDED, ALUMINUM ALLOY 6061-T6, AMS4027, MOLD IN GROOVE, NBR RUBBER, AMS-R-7362
    SAE AMS 2399 : 2011 ELECTROLESS NICKEL-BORON PLATING
    MIL-DTL-81706 Revision B:2004 Chemical Conversion Materials for Coating Aluminum and Aluminum Alloys
    SAE AMS 7258 : 2001 RINGS, SEALING, BUTADIENE-ACRYLONITRILE (NBR) RUBBER FUEL RESISTANT, LOW SHRINKAGE 65-75
    SAE AMS P 5315 : 2013 ACRYLONITRILE-BUTADIENE (NBR) RUBBER FOR FUEL-RESISTANT SEALS 60 TO 70
    SAE AMS 1541 : 2005 CLEANER, FUEL DROP TANK, WATER-SOLUBLE

    Standards Referencing This Book - (Show below) - (Hide below)

    ANSI H35.2 : 2017 DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS
    ASTM B 666/B666M : 2015 : REDLINE Standard Practice for Identification Marking of Aluminum and Magnesium Products
    SAE AMS 2772 : 2016 HEAT TREATMENT OF ALUMINUM ALLOY RAW MATERIALS
    SAE AS1990D:2003(S2016) ALUMINUM ALLOY TEMPERS
    SAE AMS 2355 : 2016 QUALITY ASSURANCE, SAMPLING AND TESTING, ALUMINUM ALLOYS AND MAGNESIUM ALLOY, WROUGHT PRODUCTS (EXCEPT FORGING STOCK), AND ROLLED, FORGED, OR FLASH WELDED RINGS
    ASTM B 660 : 2015 : REDLINE Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
    ANSI H35.2M : 2013 DIMENSIONAL TOLERANCES FOR ALUMINUM MILL PRODUCTS (METRIC)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective