UNE-EN ISO 1043-1:2012
|
Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1:2011) |
UNE-EN ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
UNE-ISO 13953:2011
|
Polyethylene (PE) pipes and fittings. Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
UNE-EN ISO 3126:2005
|
Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
ISO 4427-3:2007
|
Plastics piping systems Polyethylene (PE) pipes and fittings for water supply Part 3: Fittings |
UNE-EN 13244-3:2003
|
Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings |
UNE-EN 13244-5:2003
|
Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
ISO 12176-1:2017
|
Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
ISO 3:1973
|
Preferred numbers Series of preferred numbers |
UNE-EN 12201-4:2012
|
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves |
ISO 4433-1:1997
|
Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method |
UNE 53389:2001 IN
|
Plastics pipes and fittings. Combined chemical-resistance classification table. |
ISO 11414:2009
|
Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
UNE-EN 12201-2:2012
|
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
UNE-EN 12201-5:2012
|
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
UNE-EN 12201-1:2012
|
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
ISO 4433-2:1997
|
Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefin pipes |
UNE 53394:2006 IN
|
Plastics. Code for the installation and handling of polyethylene (PE) pipes for water piping under pressure. Recommended techniques |
UNE-EN ISO 1167-3:2008
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 3: Preparation of components (ISO 1167-3:2007) |
ISO 11357-6:2008
|
Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
ISO 9624:1997
|
Thermoplastics pipes for fluids under pressure Mating dimensions of flange adapters and loose backing flanges |
UNE-EN ISO 472:2015
|
Plastics - Vocabulary (ISO 472:2013) |
UNE-EN ISO 1133:2006
|
Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
UNE-EN 13244-4:2003
|
Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 4: Valves |