UNI EN ISO 604 : 2008

Current

Current The latest, up-to-date edition.

PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES

Available format(s):

Language(s):

Published date: 22-10-2008

Publisher: Ente Nazionale Italiano di Unificazione (UNI)

Table of Contents - (Show below) - (Hide below)

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Apparatus
6 Test specimens
7 Number of test specimens
8 Conditioning of test specimens
9 Test procedure
10 Calculation and expression of results
11 Precision
12 Test report
Annex A (normative) - Small test specimens
Annex B (informative) - Limits of buckling
Annex C (normative) - Compliance correction
Annex ZA (normative) - Normative references
to international publications with
their relevant European publications
Bibliography

Abstract - (Show below) - (Hide below)

Describes a method for determining the compressive properties of plastics under defined conditions.

General Product Information - (Show below) - (Hide below)

Development Note	REPLACES UNI 4279
Document Type	Standard
ISBN
Pages
Published
Publisher	Ente Nazionale Italiano di Unificazione (UNI)
Status	Current
Supersedes	UNI 4279 : 1972 UNI EN ISO 604 : 1998

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
EN ISO 604 : 2003	Identical
NEN EN ISO 604 : 2003	Identical
UNE-EN ISO 604:2003	Identical
NF EN ISO 604 : 2004	Identical
NBN EN ISO 604 : 2003	Identical
NS EN ISO 604 : 2ED 2003	Identical
SN EN ISO 604 : 2003	Identical
BS EN ISO 604:2003	Identical
ISO 604:2002	Identical
I.S. EN ISO 604:2003	Identical
DIN EN ISO 604:2003-12	Identical
DIN EN ISO 604 E : 2003	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

13/30251579 DC : 0	BS EN 50617-1 - RAILWAYS APPLICATIONS - BASIC PARAMETERS OF TRAIN DETECTION SYSTEMS - PART 1: TRACK CIRCUITS
PREN 50617-1 : DRAFT 2013	RAILWAYS APPLICATIONS - BASIC PARAMETERS OF TRAIN DETECTION SYSTEMS - PART 1: TRACK CIRCUITS

Standards Referencing This Book - (Show below) - (Hide below)

ISO 293:2004	Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 3167:2014	Plastics Multipurpose test specimens
ISO 7616:1986	Cellular plastics, rigid — Determination of compressive creep under specified load and temperature conditions
EN ISO 10724-1 : 2001	PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOSETTING POWDER MOULDING COMPOUNDS (PMCS) - PART 1: GENERAL PRINCIPLES AND MOULDING OF MULTIPURPOSE TEST SPECIMENS
ISO 295:2004	Plastics — Compression moulding of test specimens of thermosetting materials
ISO 10724-1:1998	Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
EN ISO 2818:1996	PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING
ISO 2602:1980	Statistical interpretation of test results Estimation of the mean Confidence interval
EN ISO 3167:2014	Plastics - Multipurpose test specimens (ISO 3167:2014)
ISO 472:2013	Plastics Vocabulary
EN ISO 295 : 2004	PLASTICS - COMPRESSION MOULDING OF TEST SPECIMENS OF THERMOSETTING MATERIALS
ISO 291:2008	Plastics Standard atmospheres for conditioning and testing
ISO 3597-3:2003	Textile-glass-reinforced plastics Determination of mechanical properties on rods made of roving-reinforced resin Part 3: Determination of compressive strength
EN ISO 291:2008	Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008)
ISO 5893:2002	Rubber and plastics test equipment Tensile, flexural and compression types (constant rate of traverse) Specification
ISO 7743:2017	Rubber, vulcanized or thermoplastic Determination of compression stress-strain properties
ISO 294-1:2017	Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 2818:1994	Plastics — Preparation of test specimens by machining
ISO 14126:1999	Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction
EN ISO 294-1:2017	Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017)

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart