Skip to content
Please enter a keyword to search

  • PD ISO/TR 10064-1:2017

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Code of inspection practice Measurement of cylindrical gear tooth flanks

    Available format(s):  Hardcopy, PDF

    Superseded date:  03-10-2019

    Language(s):  English

    Published date:  25-09-2017

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms, definitions, symbols and abbreviated terms
    4 General considerations
    5 Conventions and measurement positions
    6 Types of measuring equipment and principle
    7 Recommended measurement procedure and good
       measurement practice
    8 Inspection procedures for gears that are too large for
       gear inspection machines
    9 Measurement analysis - Profile, helix, pitch and
       radial runout
    10 Interpretation of profile, helix, pitch and radial
       runout results
    11 Single flank composite testing
    12 Additional measurements
    13 Filters and data density
    14 Additional calculations
    Bibliography

    Abstract - (Show below) - (Hide below)

    Gives a code of practice dealing with measurements on flanks of individual cylindrical involute gears, i.e. with the measurement of pitch, profile, helix and tangential composite characteristics.

    General Product Information - (Show below) - (Hide below)

    Committee MCE/5
    Development Note Supersedes BS ISO TR 10064-1. (10/2017)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 14638:2015 Geometrical product specifications (GPS) Matrix model
    ISO 18653:2003 Gears Evaluation of instruments for the measurement of individual gears
    ISO 701:1998 International gear notation Symbols for geometrical data
    ISO 1328-1:2013 Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth
    ISO 14253-1:2017 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications
    ISO 17450-1:2011 Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification
    ISO/TR 10064-3:1996 Code of inspection practice Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes
    ISO/TR 10064-2:1996 Code of inspection practice Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash
    ISO 21771:2007 Gears — Cylindrical involute gears and gear pairs — Concepts and geometry
    ISO 53:1998 Cylindrical gears for general and heavy engineering Standard basic rack tooth profile
    ISO 17450-2:2012 Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators, uncertainties and ambiguities
    ISO/TR 10064-4:1998 Code of inspection practice Part 4: Recommendations relative to surface texture and tooth contact pattern checking
    ISO 14253-2:2011 Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
    ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering — Modules
    ISO 15530-3:2011 Geometrical product specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 3: Use of calibrated workpieces or measurement standards
    ISO 22514-7:2012 Statistical methods in process management Capability and performance Part 7: Capability of measurement processes
    ISO/TR 10064-5:2005 Code of inspection practice Part 5: Recommendations relative to evaluation of gear measuring instruments
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective