Skip to content
Please enter a keyword to search

  • SAE AMS 6322 : 2014

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    STEEL BARS, FORGINGS, AND RINGS, 0.50CR - 0.55NI - 0.25MO (0.38 - 0.43C) (SAE 8740)

    Available format(s):  Hardcopy, PDF

    Superseded date:  03-01-2016

    Language(s):  English

    Published date:  01-01-2014

    Publisher:  SAE International

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. APPLICABLE DOCUMENTS
    3. TECHNICAL REQUIREMENTS
    4. QUALITY ASSURANCE PROVISIONS
    5. PREPARATION FOR DELIVERY
    6. ACKNOWLEDGMENT
    7. REJECTION
    8. NOTES

    Abstract - (Show below) - (Hide below)

    Specifies an aircraft-quality, low-alloy steel in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings.

    General Product Information - (Show below) - (Hide below)

    Committee AMS-E
    Development Note Supersedes MIL S 6049 (09/2002) Supersedes SAE AMS S 6049. (07/2006)
    Document Type Standard
    Publisher SAE International
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    SAE AMS 6327L : 2017 STEEL BARS AND FORGINGS, 0.50CR - 0.55NI - 0.25MO (0.38 - 0.43C) (SAE 8740), HEAT TREATED, 125 KSI (862 MPA) TENSILE STRENGTH (COMPOSITION SIMILAR TO UNS G87400)
    17/30369678 DC : 0 PREN 7010 - AEROSPACE SERIES - USER GUIDE FOR CREATION AND DESIGNATION OF BOLTS
    SAE AS 7452 : 2014 BOLTS AND SCREWS, STEEL, LOW ALLOY HEAT TREATED, ROLL THREADED
    MIL R 007885 : C SUPP 1 RIVETS; BLIND, STRUCTURAL, LOCKED AND FRICTION RETAINED SPINDLE, GENERAL SPECIFICATION FOR
    SAE AS 45909 : 2015 STUD, LOCKED IN, RING LOCKED, SERRATED, GENERAL SPECIFICATION FOR
    MIL-DTL-7885-12 Base Document:1996 RIVETS, BLIND, STRUCTURAL, 100 DEG. FLUSH HEAD, 5056 AL ALLOY SLEEVE, MECHANICALLY LOCKED CRES SPINDLE
    MIL-DTL-7885-11 Base Document:1996 RIVETS, BLIND, STRUCTURAL, UNIVERSAL PROTRUDING HEAD, 5056 AL ALLOY SLEEVE, MECHANICALLY LOCKED CRES SPINDLE (TYPE I, STYLE A, CLASS 1)
    MIL-DTL-7885-28 Base Document:1996 RIVETS, BLIND, STRUCTURAL, FLANGED DOME HEAD, 5056 AL ALLOY SLEEVE, MECHANICALLY LOCKED 8740 ALLOY STEEL SPINDLE, OVERSIZE DIAMETER (TYPE I, STYLE B, CLASS 4)
    MIL-S-45909 Revision C:1989 STUD, LOCKED IN - RING LOCKED SERRATED
    MIL-DTL-7885-27 Base Document:1996 RIVETS, BLIND, STRUCTURAL, 100 DEG. FLUSH SHEAR HEAD, 5056 AL ALLOY SLEEVE, MECHANICALLY LOCKED 8740 ALLOY STEEL SPINDLE (TYPE I, STYLE A, CLASS 3)
    MS21025 Revision F:1996 NUT, CASTELLATED, HEXAGON
    MIL-S-45915 Revision A:1967 STUD, LOCKED IN - KEY LOCKED - GENERAL SPECIFICATION FOR
    MIL-DTL-83454 Revision B:2016 TERMINALS, STUD, BLIND PLATE, FOR ELECTRICAL BONDING AND GROUNDING (NONINSULATED)
    MIL-STD-1876 Revision A:1991 NITRIDING, GASEOUS ATMOSPHERE PROCESSING FOR
    10/30227763 DC : 0 BS EN 6114 - AEROSPACE SERIES - BOLT, COUNTERSUNK HEAD, SHORT THREAD - INCH SERIES
    SAE MA 1573 : 2016 NUT, SELF-LOCKING, STEEL, CLASS 1100 MPA/235 DEGREES C, MJ THREAD PROCUREMENT SPECIFICATION FOR, METRIC
    MIL-DTL-45932 Revision A:2015 INSERT, SCREW THREAD, THIN WALL, LOCKED IN: GENERAL SPECIFICATION FOR
    10/30227764 DC : 0 BS EN 6115 - AEROSPACE SERIES - BOLT - PROTRUDING HEAD, SHORT THREAD - INCH SERIES
    DOD-N-70333 Base Document:1985 NUT, PLAIN AND SELF-LOCKING, CLINCH, METRIC (SELF-CLINCHING, KNURLED COLLAR) FIXED AND FLOATING, GENERAL SPECIFICATION FOR
    MIL-I-45914 Revision A:1991 INSERT, SCREW THREAD - LOCKED IN, KEY LOCKED
    DOD-S-63543 Base Document:1982 STUD & ROD, THREADED, METRIC, GENERAL SPECIFICATION FOR
    SAE AS 7252 : 2015 NUTS, SELF-LOCKING, STEEL HIGH STRENGTH, ALL METAL 450 DEGREES F USE, UN AND UNJ THREAD FORM
    DOD-S-63275 Revision A:1982 STUD, SCREW THREAD, LOCKED IN, RING LOCKED, SERRATED, METRIC AND RING LOCK SERRATED METRIC, GENERAL SPECIFICATION FOR
    SAE AS 7456 : 2016 STUDS, STEEL, LOW ALLOY, HEAT TREATED, ROLL THREADED
    MIL-DTL-8789 Revision G:2015 FITTING END, ATTACHABLE, HYDRAULIC, HIGH PRESSURE (3,000 PSI), GENERAL SPECIFICATION FOR
    MIL-R-7885 Revision D:1988 RIVET, BLIND, STRUCTURAL, MECHANICALLY LOCKED SPINDLE AND FRICTION LOCKED SPINDLE, GENERAL SPECIFICATION FOR
    DOD-I-63276 Revision A:1983 INSERT, SCREW THREAD, LOCKED IN, RING LOCKED, SERRATED, METRIC AND RING LOCK SERRATED METRIC
    SAE AS 269J:2012:(S2018) IDENTIFICATION OF MATERIAL FOR AN, MS AND AS ENGINE AND PROPELLER STANDARD UTILITY PARTS AND ALSO FOR COMPANY PARTS
    AN103901THRUAN104000 Revision 3:1986 BOLT - DRILLED HEX HEAD, 6 HOLES, .3125-24
    SAE MA 3376 : 2018 Bolts & Screws, UNS G87400 Tensile Strength 860 MPa & 1000 MPa Procurement Specification, Metric

    Standards Referencing This Book - (Show below) - (Hide below)

    SAE AMS 2372 : 2014 QUALITY ASSURANCE SAMPLING AND TESTING, CARBON AND LOW-ALLOY STEEL FORGINGS
    SAE AMS 2370 : 2016 QUALITY ASSURANCE SAMPLING AND TESTING, CARBON AND LOW-ALLOY STEEL WROUGHT PRODUCTS AND FORGING STOCK
    ASTM E 384 : 2017 : REDLINE Standard Test Method for Microindentation Hardness of Materials
    SAE AMS 2251 : 2013 TOLERANCES, LOW-ALLOY STEEL BARS
    SAE AMS 2806D : 2013 IDENTIFICATION BARS, WIRE, MECHANICAL TUBING, AND EXTRUSIONS, CARBON AND ALLOY STEELS AND CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS
    SAE AMS 2301 : 2015 STEEL CLEANLINESS, AIRCRAFT QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE
    SAE AS 1182 : 2012 STANDARD STOCK REMOVAL ALLOWANCE AIRCRAFT-QUALITY AND PREMIUM AIRCRAFT-QUALITY STEEL BARS AND MECHANICAL TUBING
    SAE AMS 7496 : 2012 RINGS, FLASH WELDED CARBON AND LOW-ALLOY STEELS
    ASTM E 350 : 2012-09 TEST METHODS FOR CHEMICAL ANALYSIS OF CARBON STEEL, LOW-ALLOY STEEL, SILICON ELECTRICAL STEEL, INGOT IRON, AND WROUGHT IRON
    ASTM E 381 : 2017 : REDLINE Standard Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings
    SAE AMS 2808 : 2017 IDENTIFICATION FORGINGS
    SAE AMS 2259 : 2012 CHEMICAL CHECK ANALYSIS LIMITS, WROUGHT LOW-ALLOY AND CARBON STEELS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective