|
IEC 61025:2006
|
Fault tree analysis (FTA) |
|
IEC 61123:1991
|
Reliability testing - Compliance test plans for success ratio |
|
IEC 60863:1986
|
Presentation of reliability, maintainability and availability predictions |
|
ISO 2859-3:2005
|
Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures |
|
IEC 60605-4:2001
|
Equipment reliability testing - Part 4: Statistical procedures for exponential distribution - Point estimates, confidence intervals, prediction intervals and tolerance intervals |
|
IEC 60319:1999
|
Presentation and specification of reliability data for electronic components |
|
IEC 60812:2006
|
Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
|
IEC 60300-3-3:2017
|
Dependability management - Part 3-3: Application guide - Life cycle costing |
|
ISO 3951:1989
|
Sampling procedures and charts for inspection by variables for percent nonconforming |
|
IEC 61649:2008
|
Weibull analysis |
|
IEC 61014:2003
|
Programmes for reliability growth |
|
IEC 60605-6:2007
|
Equipment reliability testing - Part 6: Tests for the validity and estimation of the constant failure rate and constant failure intensity |
|
IEC 60706-3:2006
|
Maintainability of equipment - Part 3: Verification and collection, analysis and presentation of data |
|
IEC 61078:2016
|
Reliability block diagrams |
|
IEC 61165:2006
|
Application of Markov techniques |
|
ISO 2859-2:1985
|
Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
|
ISO 2859-0:1995
|
Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system |
|
IEC 61163-1:2006
|
Reliability stress screening - Part 1: Repairable assemblies manufactured in lots |
|
ISO 8422:2006
|
Sequential sampling plans for inspection by attributes |
|
IEC 61124:2012
|
Reliability testing - Compliance tests for constant failure rate and constant failure intensity |
|
IEC 60300-3-1:2003
|
Dependability management - Part 3-1: Application guide - Analysis techniques for dependability - Guide on methodology |
|
ISO/TR 8550:1994
|
Guide for the selection of an acceptance sampling system, scheme or plan for inspection of discrete items in lots |
|
IEC 61164:2004
|
Reliability growth - Statistical test and estimation methods |
|
IEC 61703:2016
|
Mathematical expressions for reliability, availability, maintainability and maintenance support terms |
|
IEC 60300-3-7:1999
|
Dependability management - Part 3-7: Application guide - Reliability stress screening of electronic hardware |
|
IEC 61709 : 3.0
|
ELECTRIC COMPONENTS - RELIABILITY - REFERENCE CONDITIONS FOR FAILURE RATES AND STRESS MODELS FOR CONVERSION |
|
IEC 60300-3-9:1995
|
Dependability management - Part 3: Application guide - Section 9: Risk analysis of technological systems |
|
IEC 60706-5:2007
|
Maintainability of equipment - Part 5: Testability and diagnostic testing |
|
IEC 61650:1997
|
Reliability data analysis techniques - Procedures for comparison of two constant failure rates and two constant failure (event) intensities |
|
IEC 60706-6:1994
|
Guide on maintainability of equipment - Part 6: Section 9: Statistical methods in maintainability evaluation |
|
IEC 61710:2013
|
Power law model - Goodness-of-fit tests and estimation methods |
|
IEC 60300-3-5:2001
|
Dependability management - Part 3-5: Application guide - Reliability test conditions and statistical test principles |