Skip to content
Please enter a keyword to search

  • 05/30132920 DC : DRAFT APR 2005

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR THE EXECUTION OF STEEL STRUCTURES

    Available format(s): 

    Superseded date:  31-12-2008

    Language(s): 

    Published date:  23-11-2012

    Publisher:  British Standards Institution

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Definitions
    4 Specifications and documentation
    5 Constituent products
    6 Fabrication
    7 Welding
    8 Mechanical fastening
    9 Erection
    10 Surface treatment
    11 Geometrical tolerances
    12 Inspection, testing and correction
    Annex A 1 (normative) List of required additional information
    Annex A 2 (normative) List of options to be specified
    Annex A 3 (normative) Requirements related to the execution classes
    Annex B (informative) Guidance for the choice of execution classes
    Annex C (informative) Typical format for a quality plan
            C.1 Scope
            C.2 Management
            C.3 Specification review
            C.4 Documentation
            C.5 Inspection and testing procedures
    Annex D (informative) Selection and use of mechanical
            fasteners for sheeting
            D.1 Scope
            D.2 Selection of fastener type
            D.3 Use of Special fasteners
    Annex E (informative) Welded joints in hollow sections
            E.1 Guidance for start and stop positions
            E.2 Preparation of joint faces
            E.3 Assembly for welding
    Annex F (informative) Welding methods for thin gauge steel
            components
            F.1 Intermittent welding
            F.2 Lap joints
            F.3 Butt welds
    Annex G (normative) Procedure test for determination of
            slip factor
            G.1 The purpose of testing
            G.2 Significant variables
            G.3 Test specimens
            G.4 Test procedure
            G.5 Extended creep test
            G.6 Test results
    Annex H (normative) Use of compressible washer-type direct
            tension indicators
            H.1 Fitting
            H.2 Checking
    Annex J (informative) Hexagon injection bolts
            J.1 General
            J.2 Hole sizes
            J.3 Bolts
            J.4 Washers
            J.5 Nuts
            J.6 Resin
            J.7 Tightening
            J.8 Installation
    Annex K (normative) Corrosion protection
            K.1 General
            K.2 Surface preparation for carbon steels
            K.3 Welds and surfaces for welding
            K.4 Surfaces in non-friction-grip preloaded connections
            K.5 Preparation of fasteners
            K.6 Coating methods
    Annex L 1 Geometrical tolerances - Essential
              tolerances (normative)
    Annex L 2 Geometrical tolerances - Supplementary
              tolerances (informative)
    Annex M (normative) Sequential method for bolt
            tightening inspection
            M.1 General
            M.2 Application
    Bibliography

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee B/521
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 12073 : 1999 WELDING CONSUMABLES - TUBULAR CORED ELECTRODES FOR METAL ARC WELDING WITH OR WITHOUT A GAS SHIELD OF STAINLESS AND HEAT-RESISTING STEELS - CLASSIFICATION
    EN 10162:2003 Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances
    PREN 14399-2 : DRAFT 2013 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 2: SUITABILITY TEST FOR PRELOADING
    PREN 15048-2 : DRAFT 2014 NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE
    EN ISO 10511:2012 Prevailing torque type hexagon thin nuts (with non-metallic insert) (ISO 10511:2012)
    EN 10048:1996 Hot rolled narrow steel strip - Tolerances on dimensions and shape
    EN 10051:2010 Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
    ISO 1479:2011 Hexagon head tapping screws
    EN 439 : 1994 WELDING CONSUMABLES - SHIELDING GASES FOR ARC WELDING AND CUTTING
    EN ISO 6789:2003 Assembly tools for screws and nuts - Hand torque tools - Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure (ISO 6789:2003)
    EN ISO 7040:2012 Prevailing torque type hexagon regular nuts (with non-metallic insert) - Property classes 5, 8 and 10 (ISO 7040:2012)
    EN 440 : 1994 WELDING CONSUMABLES - WIRE ELECTRODES AND DEPOSITS FOR GAS SHIELDED METAL ARC WELDING OF NON ALLOY AND FINE GRAIN STEELS - CLASSIFICATION
    EN 10140:2006 Cold rolled narrow steel strip - Tolerances on dimensions and shape
    EN 10079:2007 Definition of steel products
    EN 10025-4:2004 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
    EN 10149-1:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions
    EN 10027-2:2015 DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM
    EN 10029:2010 Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
    EN ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009)
    EN 10056-2:1993 Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions
    PREN 14399-5 : DRAFT 2013 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS
    EN 756:2004 Welding consumables - Solid wires, solid wire-flux and tubular cored electrode-flux combinations for submerged arc welding of non alloy and fine grain steels - Classification
    EN 10164:2004 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
    EN ISO 7042:2012 Prevailing torque type all-metal hexagon high nuts - Property classes 5, 8, 10 and 12 (ISO 7042:2012)
    EN 10279:2000 Hot rolled steel channels - Tolerances on shape, dimensions and mass
    EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
    EN ISO 15979 : 2002 OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND PROTRUDING HEAD ST/ST
    PREN 13479 : DRAFT 2014 WELDING CONSUMABLES - GENERAL PRODUCT STANDARD FOR FILLER METALS AND FLUXES FOR FUSION WELDING OF METALLIC MATERIALS
    ISO 10509:2012 Hexagon flange head tapping screws
    EN 10149-2:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels
    EN 10034:1993 Structural steel I and H sections - Tolerances on shape and dimensions
    EN ISO 7719:2012 Prevailing torque type all-metal hexagon regular nuts - Property classes 5, 8 and 10 (ISO 7719:2012)
    ISO 7049:2011 Cross-recessed pan head tapping screws
    EN 12535 : 2000 WELDING CONSUMABLES - TUBULAR CORED ELECTRODES FOR GAS SHIELDED METAL ARC WELDING OF HIGH STRENGTH STEELS - CLASSIFICATION
    EN ISO 15976 : 2002 CLOSED END BLIND RIVETS WITH BREAK PULL MANDREL AND PROTRUDING HEAD - ST/ST
    PREN 14399-4 : DRAFT 2013 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES
    EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
    EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
    EN 10088-2:2014 STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES
    EN 10131:2006 (edition 2) Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape
    EN 10024:1995 Hot rolled taper flange I sections - Tolerances on shape and dimensions
    EN 10210-1:2006 Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions
    EURONORM 60 : 1977 HOT-ROLLED ROUND STEEL FOR GENERAL USE
    EN 10327:2004 Continuously hot-dip coated strip and sheet of low carbon steels for cold forming - Technical delivery conditions
    EN 10028-7:2016 Flat products made of steels for pressure purposes - Part 7: Stainless steels
    EN ISO 1127:1996 Stainless steel tubes - Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992)
    EN 10210-2:2006/AC:2007 HOT FINISHED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 2: TOLERANCES, DIMENSIONS AND SECTIONAL PROPERTIES
    EN 10326:2004 Continuously hot-dip coated strip and sheet of structural steels - Technical delivery conditions
    EN 10163-2:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats
    EN 10163-1:2004/AC:2007 DELIVERY REQUIREMENTS FOR SURFACE CONDITION OF HOT-ROLLED STEEL PLATES, WIDE FLATS AND SECTIONS - PART 1: GENERAL REQUIREMENTS
    EN 10272:2016 Stainless steel bars for pressure purposes
    EN 10219-1:2006 Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions
    ISO 1481:2011 Slotted pan head tapping screws
    EN 10143:2006 (edition 2) Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape
    EURONORM 65 : 1980 HOT-ROLLED ROUND STEEL FOR SCREWS AND RIVETS
    EN 10021:2006 General technical delivery conditions for steel products
    EURONORM 61 : 1982 HOT-ROLLED HEXAGON STEEL
    EURONORM 58 : 1978 HOT-ROLLED FLAT STEEL FOR GENERAL USE
    EN ISO 2320:2015 Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015)
    PREN 14399-3 : DRAFT 2013 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES
    EN ISO 10513:2012 Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread - Property classes 8, 10 and 12 (ISO 10513:2012)
    EN 10025-5:2004 Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
    EN 10163-3:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections
    EN 12072 : 1999 WELDING CONSUMABLES - WIRE ELECTRODES, WIRES AND RODS FOR ARC WELDING OF STAINLESS AND HEAT-RESISTING STEELS - CLASSIFICATION
    EN 760:1996 Welding consumables - Fluxes for submerged arc welding - Classification
    EN 10204:2004 Metallic products - Types of inspection documents
    EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
    ISO 4997:2015 Cold-reduced carbon steel sheet of structural quality
    EN 1600:1997 Welding consumables - Covered electrodes for manual arc welding of stainless and heat resisting steels - Classification
    EN 499 : 1994 WELDING CONSUMABLES - COVERED ELECTRODES FOR MANUAL METAL ARC OF NON ALLOY AND FINE GRAIN STEELS - CLASSIFICATION
    EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
    EN 10027-1:2016 Designation systems for steels - Part 1: Steel names
    EN 10025-6:2004+A1:2009 Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
    PREN 14399-8 : DRAFT 2015 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES
    EN 10020:2000 Definition and classification of grades of steel
    EN 10219-2:2006 Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 2: Tolerances, dimensions and sectional properties
    EN 758 : 1997 WELDING CONSUMABLES - TUBULAR COVERED ELECTRODES FOR METAL ARC WELDING WITH AND WITHOUT A GAS SHIELD OF NON ALLOY AND FINE GRAIN STEELS - CLASSIFICATION
    EN ISO 10684:2004/AC:2009 Fasteners - Hot dip galvanized coatings (ISO 10684:2004/Cor 1:2008)
    EN ISO 15980 : 2002 OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND COUNTERSUNK HEAD ST/ST
    EN ISO 15480 : 1999 HEXAGON WASHER HEAD DRILLING SCREWS WITH TAPPING SCREW THREAD
    EN 10055:1995 Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions
    EURONORM 59 : 1978 HOT-ROLLED SQUARE STEEL FOR GENERAL USE
    EN 10258 : 1997 COLD-ROLLED STAINLESS STEEL AND NARROW STRIP AND CUT LENGTHS - TOLERANCES AND DIMENSIONS AND SHAPE
    PREN 14399-7 : DRAFT 2015 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES
    PREN 10217-7 : DRAFT 2009 WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 7: STAINLESS STEEL TUBES
    PREN 14399-9 : DRAFT 2015 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES
    EN ISO 15984 : 2002 OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND COUNTERSUNK HEAD A2/A2
    EN 10025-3:2004 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
    EN ISO 15983 : 2002 OPEN END BLIND RIVETS WITH BREAK PULL MANDREL AND PROTRUDING HEAD A2/A2
    EN 10259 : 1997 COLD-ROLLED STAINLESS STEEL WIDE STRIP AND PLATE/SHEET - TOLERANCES ON DIMENSIONS AND SHAPE
    EN ISO 10512:2012 Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread - Property classes 6, 8 and 10 (ISO 10512:2012)
    EN 12534 : 1999 WELDING CONSUMABLES - WIRE ELECTRODES, WIRES, RODS AND DEPOSITS FOR GAS SHIELDED METAL ARC WELDING OF HIGH STRENGTH STEELS - CLASSIFICATION
    EN 10149-3:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels
    EN 757:1997 Welding consumables - Covered electrodes for manual metal arc welding of high strength steels - Classification
    EURONORM 17 : 1970 WIRE ROD OF COMMON UNALLOYED STEELS FOR DRAWING; DIMENSIONS AND PERMISSIBLE DEVIATIONS
    EN ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009)
    PREN 14399-6 : DRAFT 2013 HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective