09/30181595 DC : 0

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions
4 General description
   4.2 Colour type
   4.3 xy-coordinate
   4.4 Colour temperature T[c]
   4.5 Colour type: primary N
   4.6 Colour type: RGBWAF
   4.7 Multi colour type control gear
5 Electrical specification
6 Interface power supply
7 Transmission Protocol Structure
8 Timing
9 Method of operation
   9.1 Colour light output versus arc power level
   9.2 Power On
        9.2.1 Store power on colour
        9.2.2 Query power on colour
   9.3 System-failure
        9.3.1 Store system failure colour
        9.3.2 Query system failure colour
   9.4 Min and Max level
   9.5 Fade time and fade rate
   9.9 8-bit and 16-bit data mode
   9.10 Multi colour type control gear
   9.11 Colour scenes
        9.11.1 Store colour scene X
        9.11.2 Remove colour scene X
        9.11.3 Go to colour scene X
        9.11.4 Query colour scene X
   9.12 Colour change
        9.12.1 Colour type xy-coordinate
        9.12.2 Colour type colour temperature T[c]
        9.12.3 Colour type change
   9.13 Sequencer scenes
        9.13.1 Store colour sequencer scene X
        9.13.2 Query colour sequencer scene X
10 Declaration of variables
11 Definition of commands
        11.3.1 Queries related to status information
        11.3.4 Application extended commands
               11.3.4.1 Application extended control commands
               11.3.4.2 Application extended configuration
                         commands
               11.3.4.3 Application extended query commands
        11.4.4 Extended special commands
   11.5 Summary of the command set
        11.5.4 Cross-command table
        11.5.5 DTR, DTR1 and DTR2 cross-table
12 Test procedures
   12.4 Test sequence 'Physical address allocation'
   12.7 Test sequences 'Application extended commands for device
        type 8'
        12.7.1 Test sequences 'APPLICATION EXTENDED QUERY COMMANDS'
               12.7.1.1 Test sequence 'QUERY GEAR FEATURES/STATUS'
               12.7.1.2 Test sequence 'QUERY COLOUR STATUS'
               12.7.1.3 Test sequence 'QUERY COLOUR TYPE FEATURES'
               12.7.1.4 Test sequence 'QUERY COLOUR VALUE'
               12.7.1.5 Test sequence 'QUERY RGBWAF CONTROL'
               12.7.1.6 Test sequence 'QUERY ASSIGNED COLOUR'
               12.7.1.7 Test sequence 'QUERY STORED COLOUR TYPE'
               12.7.1.8 Test sequence 'QUERY STORED COLOUR VALUE'
        12.7.2 Test sequences 'Application extended configuration
               commands'
               12.7.2.1 Test sequence 'START IDENTIFICATION'
               12.7.2.2 Test sequence 'STORE TY PRIMARY N'
               12.7.2.3 Test sequence 'STORE xy-COORDINATE PRIMARY N'
               12.7.2.4 Test sequence 'STORE COLOUR TEMPERATURE T[c]
                         LIMIT'
               12.7.2.5 Test sequence 'STORE GEAR FEATURES'
               12.7.2.6 Test sequence 'STORE COLOUR SCENE'
               12.7.2.7 Test sequence 'ASSIGN COLOUR TO ACTIVE CHANNEL'
               12.7.2.8 Test sequence 'START AUTO CALIBRATION'
               12.7.2.9 Test sequence 'POWER ON COLOUR'
               12.7.2.10 Test sequence 'SYSTEM FAILURE'
        12.7.3 Test sequences 'ENABLE DEVICE TYPE'
               12.7.3.1 Test sequence 'ENABLE DEVICE TYPE: Application
               extended commands'
               12.7.3.2 Test sequence 'ENABLE DEVICE TYPE: Application
               extended configuration commands'
        12.7.4 Test sequences 'Application extended control commands'
                12.7.4.1 Test sequence 'SET TEMPORARY x-COORDINATE'
                12.7.4.2 Test sequence 'SET TEMPORARY y-COORDINATE'
                12.7.4.3 Test sequence 'ACTIVATE xy-COORDINATE'
                12.7.4.4 Test sequence 'x-COORDINATE STEP UP'
                12.7.4.5 Test sequence 'x-COORDINATE STEP DOWN'
                12.7.4.6 Test sequence 'y-COORDINATE STEP UP'
                12.7.4.7 Test sequence 'y-COORDINATE STEP DOWN'
                12.7.4.8 Test sequence 'SET COLOUR TEMPERATURE T[c]'
                12.7.4.9 Test sequence 'COLOUR TEMPERATURE T[c] STEP
                COLDER'
                12.7.4.10 Test sequence 'COLOUR TEMPERATURE T[c] STEP
                WARMER'
                12.7.4.11 Test sequence 'SET PRIMARY N DIMLEVEL'
                12.7.4.12 Test sequence 'SET RGB DIMLEVEL'
                12.7.4.13 Test sequence 'SET WAF DIMLEVEL'
                12.7.4.14 Test sequence 'SET RGBWAF CONTROL'
        12.7.5 Test sequences 'Application extended miscellaneous'
        12.7.6 Test sequences 'Standard application extended
                commands'
                12.7.6.1 Test sequences 'QUERY EXTENDED VERSION
                NUMBER'
                12.7.6.2 Test sequence 'RESERVED APPLICATION EXTENDED
                COMMANDS'

BS EN 62386-209