09/30181599 DC : 0

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions
   3.18 Multi channel device
   3.19 Point
   3.20 Next Point
   3.21 Previous point
   3.22 Pointer
4 General description
5 Electrical specification
6 Basic requirements for interface power supplies
7 Transmission protocol structure
8 Timing
9 Method of operation
   9.2 Power-On
   9.3 Interface-failure
   9.7 Multi channel device
   9.8 Sequencer operation
        9.8.1 Externally driven sequencer mode
        9.8.2 Automatic sequencer mode
               9.8.2.1 Sequencer programming
               9.8.2.2 Sequence programming example
               9.8.2.3 Starting the automatic sequencer
                         9.8.2.3.1 Starting with sequencer
                                   commands
                         9.8.2.3.2 Starting with pointer
               9.8.2.4 Stopping the automatic sequencer
10 Declaration of variables
11 Definition of commands
   11.1.1 Direct arc power control command
   11.1.2 Indirect arc power control commands
   11.2.1 General configuration commands:
   11.3.1 Queries related to status information
   11.3.2 Queries related to arc power parameter settings
   11.3.4 Application extended commands
          11.3.4.1 Application extended configuration commands
          11.3.4.2 Application extended control commands
          11.3.4.3 Application extended query commands
   11.4.4 Extended special commands
   11.5 Summary of the command set
12 Test procedures
   12.4 Test sequence 'Physical address allocation'
   12.7 Test sequences 'Application extended commands for
        device type 9'
        12.7.1 Test sequences 'APPLICATION EXTENDED QUERY
               COMMANDS'
               12.7.1.1 Test sequence 'QUERY FEATURES'
        12.7.2 Test sequences 'Application extended
               configuration commands'
               12.7.2.1 Test sequence 'Configure POINT N'
               12.7.2.2 Test sequence 'Configuration - sent
                         twice'
               12.7.2.3 Test sequence 'Configuration -
                         time-out'
               12.7.2.4 Test sequence 'Configuration -
                         command in-between 1'
               12.7.2.5 Test sequence 'Configuration -
                         command in-between 2'
               12.7.2.6 Test sequence 'COPY TO POINT N'
               12.7.2.7 Test sequence 'COPY TO POINT N -
                         sent twice'
               12.7.2.8 Test sequence 'COPY TO POINT N -
                         time-out'
               12.7.2.9 Test sequence 'COPY TO POINT N -
                         command in-between'
               12.7.2.10 Test sequence 'CHANNEL SELECTION'
               12.7.2.11 Test sequence 'CHANNEL SELECTION -
                         sent twice/time-out'
               12.7.2.12 Test sequence 'CHANNEL SELECTION -
                         command in-between'
               12.7.2.13 Test sequence 'CONFIGURE CONTROL N'
               12.7.2.14 Test sequence 'CONFIGURE CONTROL N -
                         sent twice/time-out'
               12.7.2.15 Test sequence "CONFIGURE CONTROL N -
                         command in-between"
        12.7.3 Test sequences 'ENABLE DEVICE TYPE'
               12.7.3.1 Test sequence 'ENABLE DEVICE TYPE:
                         Application extended commands'
               12.7.3.2 Test sequence 'ENABLE DEVICE TYPE:
                         Application extended configuration
                         commands 1'
               12.7.3.3 Test sequence 'ENABLE DEVICE TYPE:
                         Application extended configuration
                         commands 2'
        12.7.4 Test sequences 'Application extended control
               commands'
               12.7.4.1 Subsequence 'Configure sequence'
               12.7.4.2 Test sequence 'GO TO POINT N'
               12.7.4.3 Test sequence 'GO TO NEXT POINT'
               12.7.4.4 Test sequence 'GO TO PREVIOUS POINT'
               12.7.4.5 Test sequence 'Automatic sequence'
               12.7.4.6 Test sequence 'Automatic sequence -
                         pointer'
               12.7.4.7 Test sequence 'Automatic sequence -
                         number of runs'
               12.7.4.8 Test sequence 'Automatic sequence -
                         stopped by command'
               12.7.4.9 Test sequence 'Sequencer performance'
               12.7.4.10 Test sequence 'START AT POINT N -
                         number of runs'
        12.7.5 Test sequences 'Application extended
               miscellaneous'
               12.7.5.1 Test sequence 'RESET SEQUENCER'
               12.7.5.2 Test sequence 'RESET SEQUENCER -
                         send twice/time-out'
               12.7.5.3 Test sequence 'RESET SEQUENCER -
                         command in-between'
               12.7.5.4 Test sequence 'RESET CONTROL N'
               12.7.5.5 Test sequence 'FAULTY CHANNEL'
        12.7.6 Test sequences 'Standard application extended
               commands'
               12.7.6.1 Test sequences 'QUERY EXTENDED VERSION
                         NUMBER'
               12.7.6.2 Test sequence 'RESERVED APPLICATION
                         EXTENDED COMMANDS'
BIBLIOGRAPHY

BS EN 62386-210