10/30212150 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 12201-3 - PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - PART 3: FITTINGS
Hardcopy , PDF
30-11-2011
English
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 Material
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics
8 Physical characteristics
9 Chemical resistance of fittings in contact with
chemicals
10 Performance requirements
11 Marking
12 Delivery Conditions
Annex A (normative) - Socket fusion fittings
Annex B (normative) - Fabricated fittings
Annex C (informative) - Examples of typical terminal
connection for electrofusion fittings
Annex D (normative) - Short-term pressure test method
Annex E (normative) - Tensile test for fitting/pipe
assemblies
Bibliography
BS EN 12201-3
| Committee |
PRI/88/2
|
| DocumentType |
Draft
|
| Pages |
41
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 12201-3 : DRAFT 2010 | Identical |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| ISO/TR 10358:1993 | Plastics pipes and fittings Combined chemical-resistance classification table |
| ISO 13953:2001 | Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 4433-1:1997 | Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method |
| IEC 60364-1:2005 | Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions |
| EN 1716:1997 | Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an assembled tapping tee |
| CEN/TR 15438:2007 | Plastics piping systems - Guidance for coding of products and their intended uses |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| PREN 12201-1 : DRAFT 2010 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 1: GENERAL |
| EN ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007) |
| ISO 14236:2000 | Plastics pipes and fittings Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 4433-2:1997 | Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefin pipes |
| IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV | Low-voltage switchgear and controlgear - Part 1: General rules |
| ISO 13954:1997 | Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| ISO 13955:1997 | Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies |
| PREN 12201-5 : DRAFT 2010 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| ISO 9624:1997 | Thermoplastics pipes for fluids under pressure Mating dimensions of flange adapters and loose backing flanges |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| ISO 4059:1978 | Polyethylene (PE) pipes — Pressure drop in mechanical pipe-jointing systems — Method of test and requirements |
| ISO 13950:2007 | Plastics pipes and fittings Automatic recognition systems for electrofusion joints |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 13951:2015 | Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading |
| PREN 12201-2 : DRAFT 2010 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES |
| CEN/TS 12201-7:2014 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
| EN ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 3: Preparation of components (ISO 1167-3:2007) |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.