Skip to content
Please enter a keyword to search

  • 10/30218092 DC : 0

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    BS EN 15502-1 - GAS-FIRED HEATING BOILERS - PART 1: GENERAL REQUIREMENTS AND TESTS

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-07-2012

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms, definitions and symbols
    4 Classification
    5 Construction
    6 Electrical safety
    7 Controls
    8 Safety of operation
    9 Useful efficiencies
    10 Electric auxiliary energy
    11 Risk assessment
    12 Marking and instructions
    Annex A (informative) - Properties of carbon and stainless steels
    Annex B (normative) - Minimum requirements for cast iron
    Annex C (normative) - Parts cast in aluminium and aluminium
                          alloys
    Annex D (normative) - Parts cast in copper or copper alloys
    Annex E (normative) - Minimum thicknesses for rolled parts
    Annex F (normative) - Nominal minimum thicknesses of boiler
            sections of cast materials under water pressure
    Annex G (normative) - Parameters for welded joints and welding
            processes
    Annex H (informative) - Composition of the gas circuit
    Annex I (informative) - Compilation of the test conditions
            for the various gas families
    Annex J (informative) - Calculation of conversions of NO[x]
    Annex K (informative) - Example of calculation of the weighting
            factors NO[x]
    Annex L (informative) - Practical method of calibrating the
            test rig to enable the heat loss Dp to be determined
    Annex M (informative) - Means of determining the ignition time at
            full rate
    Annex N (informative) - Determination of the heat losses from the
            test rig of the indirect method and contributions of the
            circulating pump of the test rig
    Annex O (informative) - Example of a risk assessment method
    Annex P (informative) - Examples of risk assessment with a method
            described in Annex O
    Annex Q (informative) - Realization of a protective measure
    Annex R (informative) - Overall classification of a basic risk
    Annex S (informative) - Not exhaustive list of classification
            examples
    Annex ZA (informative) - Clauses of this European standard
             addressing essential requirements or provisions
             of EU Directives
    Bibliography

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee GSE/29
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 2553:2013 Welding and allied processes Symbolic representation on drawings Welded joints
    IEC 60335-2-102:2004+AMD1:2008+AMD2:2012 CSV Household and similar electrical appliances - Safety - Part 2-102:Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections
    IEC 60730-2-9:2015 RLV Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls
    ISO 274:1975 Copper tubes of circular section — Dimensions
    EN 10029:2010 Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
    EN 12067-2:2004 Gas/air ratio controls for gas burners and gas burning appliances - Part 2: Electronic types
    EN 1057:2006+A1:2010 Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications
    EN 60730-2-9:2010 Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls
    EN 13203-1:2015 Gas fired domestic appliances producing hot water - Part 1: Assessment of performance of hot water deliveries
    EN 12067-1 : 98 AMD 1 2003 GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 1: PNEUMATIC TYPES
    EN 1092-3:2003/AC:2007 FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 3: COPPER ALLOY FLANGES
    EN 15456:2008 Heating boilers - Electrical power consumption for heat generators - System boundaries - Measurements
    EN ISO 3166-1:2014 Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013)
    EN 161:2011+A3:2013 Automatic shut-off valves for gas burners and gas appliances
    EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
    EN 14459:2015 Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Methods for classification and assessment
    EN 1092-4:2002 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges
    ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
    EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
    EN 125:2010+A1:2015 Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    EN 126:2012 Multifunctional controls for gas burning appliances
    EN 22553:1994 Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992)
    ISO 857-1:1998 Welding and allied processes Vocabulary Part 1: Metal welding processes
    EN 13611:2015/AC:2016 SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
    CEN/TR 1749:2014 European scheme for the classification of gas appliances according to the method of evacuation of the combustion products (types)
    CR 1404:1994 Determination of emissions from appliances burning gaseous fuels during type-testing
    EN 60335-2-102:2016 Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections
    ISO 3166-1:2013 Codes for the representation of names of countries and their subdivisions Part 1: Country codes
    EN 24063 : 1992 WELDING, BRAZING, SOLDERING AND BRAZE WELDING OF METALS - NOMENCLATURE OF PROCESSES AND REFERENCE NUMBERS FOR SYMBOLIC REPRESENTATION ON DRAWINGS
    EN 60335-1:2012/A13:2017 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
    EN 298:2012 Automatic burner control systems for burners and appliances burning gaseous or liquid fuels
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    ISO 4063:2009 Welding and allied processes — Nomenclature of processes and reference numbers
    EN 1092-2:1997 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
    ISO 857-2:2005 Welding and allied processes Vocabulary Part 2: Soldering and brazing processes and related terms
    EN 88-1:2011+A1:2016 Pressure regulators and associated safety devices for gas appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective