Skip to content
Please enter a keyword to search

  • 11/30210938 DC : 0

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    BS EN 61400-4 - WIND TURBINES - PART 4: DESIGN REQUIREMENTS FOR WIND TURBINE GEARBOXES

    Available format(s):  Hardcopy, PDF

    Superseded date:  30-04-2013

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 Scope
    2 Normative References
    3 Terms and Definitions
    4 Symbols and Abbreviated Terms
    5 Design for Reliability
    6 Drivetrain Operating Conditions and Loads
    7 Gearbox Design, Rating, and Manufacturing
      Requirements
    8 Design Verification
    9 Operation, Service and Maintenance
      Requirements
    Annex A (Informative) - Examples of Drivetrain
            Interfaces and Loads Specification
    Annex B (Informative) - Gearbox Design and
            Manufacturing Considerations
    Annex C (Informative) - Bearing Design Considerations
    Annex D (Informative) - Considerations for Gearbox
            Structural Elements
    Annex E (Informative) - Recommendations for
            Lubricant Performance in Wind Turbine
            Gearboxes
    Annex F (Informative) - Design Verification Documentation
    Annex G (Informative) - Bearing Calculation Documentation
    Annex H (Informative) - Bibliography

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee PEL/88/-/4
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    ISO 5725-1:1994 Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions
    IEC 60050-415:1999 International Electrotechnical Vocabulary (IEV) - Part 415: Wind turbine generator systems
    ASTM D 892 : 2013-07 TEST METHOD FOR FOAMING CHARACTERISTICS OF LUBRICATING OILS
    ISO 4287:1997 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters
    ISO 1328-2:1997 Cylindrical gears ISO system of accuracy Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information
    ISO/TR 13593:1999 Enclosed gear drives for industrial applications
    DIN 3990-4:1987-12 CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS; CALCULATION OF SCUFFING LOAD CAPACITY
    ISO 6336-2:2006 Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting)
    ISO 13357-1:2017 Petroleum products — Determination of the filterability of lubricating oils — Part 1: Procedure for oils in the presence of water
    ASTM D 665 : 2014-11 TEST METHOD FOR RUST-PREVENTING CHARACTERISTICS OF INHIBITED MINERAL OIL IN THE PRESENCE OF WATER
    ISO 14635-1:2000 Gears — FZG test procedures — Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils
    ISO 11007:1997 Petroleum products and lubricants Determination of rust-prevention characteristics of lubricating greases
    ISO 14104:2017 Gears — Surface temper etch inspection after grinding, chemical method
    ISO 7120:1987 Petroleum products and lubricants — Petroleum oils and other fluids — Determination of rust-preventing characteristics in the presence of water
    ISO 1328-1:2013 Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth
    ISO 8579-2:1993 Acceptance code for gears Part 2: Determination of mechanical vibrations of gear units during acceptance testing
    ISO 5593:1997 Rolling bearings Vocabulary
    ISO 2394:2015 General principles on reliability for structures
    DIN 51819-1:2016-12 TESTING OF LUBRICANTS - MECHANICAL-DYNAMIC TESTING IN THE ROLLER BEARING TEST APPARATUS FE8 - PART 1: GENERAL WORKING PRINCIPLES
    IEC TS 61400-13:2001 Wind turbine generator systems - Part 13: Measurement of mechanical loads
    DIN 471:2011-04 RETAINING RINGS FOR SHAFTS - NORMAL TYPE AND HEAVY TYPE
    ISO/TR 13989-1:2000 Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears Part 1: Flash temperature method
    DIN 472:2016-10 (Draft) RETAINING RINGS FOR BORES - NORMAL TYPE AND HEAVY TYPE
    DIN 7190:2001-02 INTERFERENCE FITS - CALCULATION AND DESIGN RULES
    ISO 6336-3:2006 Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength
    ISO 2160:1998 Petroleum products Corrosiveness to copper Copper strip test
    ISO/TR 13989-2:2000 Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears Part 2: Integral temperature method
    ISO 281:2007 Rolling bearings Dynamic load ratings and rating life
    ISO 13226:2011 Rubber Standard reference elastomers (SREs) for characterizing the effect of liquids on vulcanized rubbers
    DIN 51517-3:2014-02 LUBRICANTS - LUBRICATING OILS - PART 3: LUBRICATING OILS CLP, MINIMUM REQUIREMENTS
    ISO/TR 15144-1:2014 Calculation of micropitting load capacity of cylindrical spur and helical gears Part 1: Introduction and basic principles
    ISO 6336-5:2016 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials
    ISO 14635-2:2004 Gears — FZG test procedures — Part 2: FZG step load test A10/16, 6R/120 for relative scuffing load-carrying capacity of high EP oils
    ISO/TR 10064-3:1996 Code of inspection practice Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes
    ISO 13357-2:2017 Petroleum products — Determination of the filterability of lubricating oils — Part 2: Procedure for dry oils
    AGMA 925 : A EFFECT OF LUBRICATION ON GEAR SURFACE DISTRESS
    IEC 61400-22:2010 Wind turbines - Part 22: Conformity testing and certification
    ISO/TR 1281-2:2008 Rolling bearings Explanatory notes on ISO 281 Part 2: Modified rating life calculation, based on a systems approach to fatigue stresses
    IEC 61400-3:2009 Wind turbines - Part 3: Design requirements for offshore wind turbines
    ISO/TR 14179-1:2001 Gears Thermal capacity Part 1: Rating gear drives with thermal equilibrium at 95 C sump temperature
    AGMA 9005 : E INDUSTRIAL GEAR LUBRICATION
    ISO 10474:2013 Steel and steel products — Inspection documents
    EN 12680-3:2011 Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings
    ISO 21771:2007 Gears — Cylindrical involute gears and gear pairs — Concepts and geometry
    ISO 6336-1:2006 Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors
    ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
    ISO/TR 1281-1:2008 Rolling bearings Explanatory notes on ISO 281 Part 1: Basic dynamic load rating and basic rating life
    SAE FATIGUE DESIGN HDBK : 3ED 1997 FATIGUE DESIGN HANDBOOK AE-22
    ISO 12925-1:1996 Lubricants, industrial oils and related products (class L) Family C (Gears) Part 1: Specifications for lubricants for enclosed gear systems
    ISO 6336-6:2006 Calculation of load capacity of spur and helical gears Part 6: Calculation of service life under variable load
    ISO/TR 14179-2:2001 Gears Thermal capacity Part 2: Thermal load-carrying capacity
    DIN 6892:2012-08 Drive type fastenings without taper action - Parallel keys - Calculation and design
    ISO 10825:1995 Gears — Wear and damage to gear teeth — Terminology
    ISO 8579-1:2002 Acceptance code for gear units — Part 1: Test code for airborne sound
    ISO 12107:2012 Metallic materials — Fatigue testing — Statistical planning and analysis of data
    IEC 61400-1:2005+AMD1:2010 CSV Wind turbines - Part 1: Design requirements
    ISO 76:2006 Rolling bearings Static load ratings
    ISO/TS 16281:2008 Rolling bearings Methods for calculating the modified reference rating life for universally loaded bearings
    ISO 15243:2017 Rolling bearings — Damage and failures — Terms, characteristics and causes
    DIN 743-3:2012-12 CALCULATION OF LOAD CAPACITY OF SHAFTS AND AXLES - PART 3: STRENGTH OF MATERIALS
    DIN 45667:1969-10 CLASSIFICATION METHODS FOR EVALUATION OF RANDOM VIBRATIONS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective