Skip to content
Please enter a keyword to search

  • 11/30242077 DC : DRAFT MAY 2011

    Current The latest, up-to-date edition.

    BS ISO 16486-3 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS WITH FUSION JOINTING AND MECHANICAL JOINTING - PART 3: FITTINGS

    Available format(s): 

    Language(s): 

    Published date:  23-11-2012

    Publisher:  British Standards Institution

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms, definitions, symbols and abbreviated
       terms
    4 Material
    5 General characteristics
    6 Geometrical characteristics
    7 Mechanical characteristics
    8 Physical characteristics
    9 Chemical resistance of fittings in contact with
       chemicals
    10 Performance requirements
    11 Marking
    12 Packaging
    Annex A (informative) - Examples of typical terminal
            connections for electrofusion fittings
    Annex B (normative) - Short-term pressure test method
    Annex C (normative) - Tensile test fitting/pipe assemblies
    Bibliography

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee PRI/88/2
    Document Type Draft
    Publisher British Standards Institution
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 682:2002/A1:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR SEALS USED IN PIPES AND FITTINGS CARRYING GAS AND HYDROCARBON FLUIDS
    ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
    ISO 13956:2010 Plastics pipes and fittings Decohesion test of polyethylene (PE) saddle fusion joints Evaluation of ductility of fusion joint interface by tear test
    ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
    ISO 4433-1:1997 Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method
    ISO 13957:1997 Plastics pipes and fittings — Polyethylene (PE) tapping tees — Test method for impact resistance
    IEC 60364-1:2005 Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    ISO 307:2007 Plastics Polyamides Determination of viscosity number
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
    ISO 13951:2015 Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective