• 15/30297998 DC : 0

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    BS EN 62271-212 ED 1.0 - HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 212: COMPACT EQUIPMENT ASSEMBLY FOR DISTRIBUTION SUBSTATION (CEADS)

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-01-2017

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Introduction
    1 General
    2 Normal and special service conditions
    3 Terms and definitions
    4 Ratings
    5 Design and construction
    6 Type test
    7 Routine tests
    8 Guide to the selection of CEADS for service
    9 Information to be given with enquiries, tenders
       and orders
    10 Rules for transport, installation, operation and
       maintenance
    11 Safety
    12 Influence of the product on the environment
    Annex AA (normative) - Method for testing CEADS under
             conditions of arcing due to an internal arc fault
    Annex BB (normative) - Test to verify the sound level of a
             CEADS
    Annex CC (informative) - Types and Application of CEADS
    Bibliography


    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee PEL/17/1
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    IEC 60076-15:2015 Power transformers - Part 15: Gas-filled power transformers
    IEC 60721-1:1990+AMD1:1992+AMD2:1995 CSV Classification of environmental conditions - Part 1: Environmental parameters and their severities
    IEC 61936-1:2010+AMD1:2014 CSV Power installations exceeding 1 kV a.c. - Part 1: Common rules
    EN 60068-2-75 : 2014 ENVIRONMENTAL TESTING - PART 2-75: TESTS - TEST EH: HAMMER TESTS (IEC 60068-2-75:2014)
    IEC 62271-200:2011 High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
    IEC 62271-202:2014 High-voltage switchgear and controlgear - Part 202: High-voltage/ low-voltage prefabricated substation
    IEC 62271-201:2014 High-voltage switchgear and controlgear - Part 201: AC solid-insulation enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
    IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
    IEC 60050-441:1984 International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses
    IEC 60076-10:2016 Power transformers - Part 10: Determination of sound levels
    IEC 60076-5:2006 Power transformers - Part 5: Ability to withstand short circuit
    IEEE C57.12.00 : 2015 STANDARD FOR GENERAL REQUIREMENTS FOR LIQUID-IMMERSED DISTRIBUTION, POWER, AND REGULATING TRANSFORMERS
    EN 50464-4 : 2007 AMD 1 2011 THREE-PHASE OIL-IMMERSED DISTRIBUTION TRANSFORMERS 50 HZ, FROM 50 KVA TO 2500 KVA WITH HIGHEST VOLTAGE FOR EQUIPMENT NOT EXCEEDING 36 KV - PART 4: REQUIREMENTS AND TESTS CONCERNING PRESSURISED CORRUGATED TANKS
    IEC TS 62271-210:2013 High-voltage switchgear and controlgear - Part 210: Seismic qualification for metal enclosed and solid-insulation enclosed switchgear and controlgear assemblies for rated voltages above 1 kV and up to and including 52 kV
    IEC 60721-2-2:2012 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - PART 2-2: ENVIRONMENTAL CONDITIONS APPEARING IN NATURE - PRECIPITATION AND WIND
    ISO/IEC Guide 51:2014 Safety aspects Guidelines for their inclusion in standards
    IEC 60076-3:2013 Power transformers - Part 3: Insulation levels, dielectric tests and external clearances in air
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    IEC TR 61641:2014 Enclosed low-voltage switchgear and controlgear assemblies - Guide for testing under conditions of arcing due to internal fault
    IEC 60076-1:2011 Power transformers - Part 1: General
    IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV Low-voltage switchgear and controlgear - Part 1: General rules
    IEC 62262:2002 Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
    IEC 62271-1:2017 High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
    IEC 60076-2:2011 Power transformers - Part 2: Temperature rise for liquid-immersed transformers
    IEC 60068-2-75:2014 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
    IEC 61439-1:2011 Low-voltage switchgear and controlgear assemblies - Part 1: General rules
    IEC 60721-2-4:1987+AMD1:1988 CSV CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - PART 2-4: ENVIRONMENTAL CONDITIONS APPEARING IN NATURE - SOLAR RADIATION AND TEMPERATURE
    IEC 60076-13:2006 Power transformers - Part 13: Self-protected liquid-filled transformers
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective