17/30345075 DC : 0
NA
Status of Standard is Unknown
BS EN ISO 11296-4 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES
Hardcopy , PDF
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the 'M' stage
6 Fittings at the 'M' stage
7 Ancillary components
8 Fitness for purpose of the installed lining system
at the 'I' stage
9 Installation practice
Annex A (informative) - CIPP components and their functions
Annex B (normative) - Cured-in-place pipes - Determination
of short-term flexural properties
Annex C (normative) - Cured-in-place pipes - Determination
of long-term flexural modulus under dry or wet
conditions
Annex D (normative) - Cured-in-place pipes - Determination
of long-term flexural strength under dry, wet or acidic
conditions (stress corrosion test)
Bibliography
BS EN ISO 11296-4.
| Committee |
PRI/88/3
|
| DocumentType |
Draft
|
| Pages |
51
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| ISO 8773:2006 | Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene (PP) |
| ISO 7685:1998 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of initial specific ring stiffness |
| ISO 10928:2016 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11296-1:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 1: General |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| ISO 13002:1998 | Carbon fibre — Designation system for filament yarns |
| ISO 8513:2016 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength |
| ISO 10468:2003 | Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor |
| ISO 899-2:2003 | Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading |
| ISO 14125:1998 | Fibre-reinforced plastic composites — Determination of flexural properties |
| ISO 7684:1997 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the creep factor under dry conditions |
| ISO 4435:2003 | Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U) |
| ISO 10952:2014 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.