ASTM E 2309 : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practices for Verification of Displacement Measuring Systems and Devices Used in Material Testing Machines
Hardcopy , PDF
11-11-2014
English
01-02-2005
CONTAINED IN VOL. 03.01, 2009 Provides test methods for determining the release rates of heat and visible smoke (Note 0) from materials, products, or assemblies when exposed to different levels of radiant heat.
Committee |
E 28
|
DocumentType |
Standard Practice
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1 These practices cover procedures and requirements for the calibration and verification of displacement measuring systems by means of standard calibration devices for static and quasi-static testing machines. This practice is not intended to be complete purchase specifications for testing machines or displacement measuring systems. Displacement measuring systems are not intended to be used for the determination of strain. See Practice E 83.
1.2 These procedures apply to the verification of the displacement measuring systems associated with the testing machine, such as a scale, dial, marked or unmarked recorder chart, digital display, etc. In all cases the buyer/owner/user must designate the displacement-measuring system(s) to be verified.
1.3 Since conversion factors are not required in this practice, either SI units, or inch units, can be used as the standard.
1.4 Displacement values indicated on displays/printouts of testing machine data systems-be they instantaneous, delayed, stored, or retransmitted-which are within the Classification criteria listed in , comply with Practices E 2309.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 790 : 2017 | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
ASTM D 143 : 2014 | Standard Test Methods for Small Clear Specimens of Timber |
ASTM E 2472 : 2012 : R2018 | Standard Test Method for Determination of Resistance to Stable Crack Extension under Low-Constraint Conditions |
ASTM D 198 : 2015 | Standard Test Methods of Static Tests of Lumber in Structural Sizes |
ASTM F 2077 : 2018 | Test Methods For Intervertebral Body Fusion Devices |
ASTM E 2658 : 2015 | Standard Practices for Verification of Speed for Material Testing Machines |
ASTM E 345 : 2016 | Standard Test Methods of Tension Testing of Metallic Foil |
ASTM F 2624 : 2012 : R2016 | Standard Test Method for Static, Dynamic, and Wear Assessment of Extra-Discal Single Level Spinal Constructs |
EN ISO 9513:2012/AC:2013 | Metallic materials - Calibration of extensometer systems used in uniaxial testing - Technical Corrigendum 1 (ISO 9513:2012/Cor 1:2013) |
ASTM D 7779 : 2011 | Standard Test Method for Determination of Fracture Toughness of Graphite at Ambient Temperature |
DIN EN ISO 9513:2013-05 | Metallic materials - Calibration of extensometer systems used in uniaxial testing (ISO 9513:2012 + Cor. 1:2013) |
I.S. EN ISO 9513:2012 | METALLIC MATERIALS - CALIBRATION OF EXTENSOMETER SYSTEMS USED IN UNIAXIAL TESTING (ISO 9513:2012) |
ASTM E 2658 : 2015 : REDLINE | Standard Practices for Verification of Speed for Material Testing Machines |
11/30148484 DC : 0 | BS EN ISO 9513 - METALLIC MATERIALS - CALIBRATION OF EXTENSOMETER SYSTEMS USED IN UNIAXIAL TESTING |
BS EN ISO 9513:2012 | Metallic materials. Calibration of extensometer systems used in uniaxial testing |
ISO 9513:2012 | Metallic materials — Calibration of extensometer systems used in uniaxial testing |
UNI EN ISO 9513 : 2013 | METALLIC MATERIALS - CALIBRATION OF EXTENSOMETER SYSTEMS USED IN UNIAXIAL TESTING |
ASTM E 345 : 2016 : REDLINE | Standard Test Methods of Tension Testing of Metallic Foil |
ASTM F 2624 : 2012 | Standard Test Method for Static, Dynamic, and Wear Assessment of Extra-Discal Single Level Spinal Constructs |
ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
ASTM D 7779 : 2011 : R2015 | Standard Test Method for Determination of Fracture Toughness of Graphite at Ambient Temperature |
UNE-EN ISO 9513:2013 | Metallic materials - Calibration of extensometer systems used in uniaxial testing (ISO 9513:2012, Corrected version 2015-06) |
ASTM D 198 : 2015 : REDLINE | Standard Test Methods of Static Tests of Lumber in Structural Sizes |
ASTM D 143 : 2014 : REDLINE | Standard Test Methods for Small Clear Specimens of Timber |
ASTM E 83 : 2016 : REDLINE | Standard Practice for Verification and Classification of Extensometer Systems |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.