Skip to content
Please enter a keyword to search

  • VDI 3405 Blatt 1:2013-10

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Additive manufacturing processes, rapid manufacturing - Laser sintering of polymer parts - Quality control

    Available format(s):  Hardcopy, PDF

    Superseded date:  08-04-2022

    Language(s):  German - English

    Published date:  01-10-2013

    Publisher:  Verlag des Vereins Deutscher Ingenieure

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Preliminary note
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviations
    5 Testing of the raw powder
       material
    6 Process control
    7 Testing part quality
    8 Quality standards
    9 Downstream processes
    10 Safety and the environment
    Annex
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines to processes are an inherent part of the product development process and the production of serial parts.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher Verlag des Vereins Deutscher Ingenieure
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    VDI 3405 Blatt 1.1:2017-08 (Draft) Additive manufacturing processes - Laser sintering of polymer parts - Qualification of materials
    VDI 3405 Blatt 3:2015-12 Additive manufacturing processes, rapid manufacturing - Design rules for part production using laser sintering and laser beam melting
    VDI 3405:2014-12 Additive manufacturing processes, rapid manufacturing - Basics, definitions, processes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 444:1994 Non-destructive testing - General principles for radiographic examination of metallic materials by X- and gamma-rays
    VDI 3404:2009-12 Additive fabrication - Rapid technologies (rapid prototyping) - Fundamentals, terms and definitions, quality parameters, supply agreements
    ISO 3951-1:2013 Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
    ISO 1628-1:2009 Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 1: General principles
    ISO 3167:2014 Plastics Multipurpose test specimens
    EN ISO 60:1999 Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:1977)
    DIN EN ISO 1133-2:2012-03 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011)
    EN ISO 1110:1997 PLASTICS - POLYAMIDES - ACCELERATED CONDITIONING OF TEST SPECIMENS
    ISO 9712:2012 Non-destructive testing Qualification and certification of NDT personnel
    DIN EN 473:2008-09 NON-DESTRUCTIVE TESTING - QUALIFICATION AND CERTIFICATION OF NDT PERSONNEL - GENERAL PRINCIPLES
    VDI 2209:2009-03 3D product modelling - Technical and organizational requirements - Procedures, tools, and applications - Cost-effective practical use
    ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
    EN ISO 11357-1:2016 Plastics - Differential scanning calorimetry (DSC) - Part 1: General principles (ISO 11357-1:2016)
    DIN ISO 2859-1:2014-08 SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION (ISO 2859-1:1999 + COR. 1:2001 + AMD.1:2011)
    EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
    ISO 27547-1:2010 Plastics — Preparation of test specimens of thermoplastic materials using mouldless technologies — Part 1: General principles, and laser sintering of test specimens
    DIN EN ISO 1874-2:2013-03 PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012)
    DIN EN ISO 60:2000-01 Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:1977); English version of DIN EN ISO 60
    ISO 1110:1995 Plastics Polyamides Accelerated conditioning of test specimens
    DIN ISO 3951-1:2016-06 Sampling procedures for inspection by variables - Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL (ISO 3951-1:2013); Text in German and English
    ISO 60:1977 Plastics — Determination of apparent density of material that can be poured from a specified funnel
    EN ISO 1133-2:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011)
    EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
    EN 473:2008 Non-destructive testing - Qualification and certification of NDT personnel - General principles
    VDI 3405 Blatt 2:2013-08 Additive manufacturing processes, rapid manufacturing - Beam melting of metallic parts - Qualification, quality assurance and post processing
    EN ISO 1874-2:2012 Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012)
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 1874-2:2012 Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    EN ISO 9712:2012 Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012)
    ISO 6186:1998 Plastics — Determination of pourability
    EN ISO 3167:2014 Plastics - Multipurpose test specimens (ISO 3167:2014)
    VDI 1000:2017-02 VDI Standardisation Work - Principles and procedures
    EN ISO 1133-1:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
    DIN EN 16016-2:2012-01 NON DESTRUCTIVE TESTING - RADIATION METHODS - COMPUTED TOMOGRAPHY - PART 2: PRINCIPLE, EQUIPMENT AND SAMPLES
    DIN EN ISO 1628-1:2012-10 Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometer - Part 1: General principles (ISO 1628-1:2009 + Amd 1:2012); German version EN ISO 1628-1:2009 + A1:2012
    DIN EN ISO 6186:1998-08 Plastics - Determination of pourability (ISO 6186:1998)
    EN ISO 11358 : 1997 PLASTICS - THERMOGRAVIMETRY (TG) OF POLYMERS - GENERAL PRINCIPLES
    ISO 3274:1996 Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments
    ISO 61:1976 Plastics — Determination of apparent density of moulding material that cannot be poured from a specified funnel
    DIN EN ISO 61:2000-01 Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:1976); English version of DIN EN ISO 61
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    DIN EN 13068-3:2001-12 NON-DESTRUCTIVE TESTING - RADIOSCOPIC TESTING - PART 3: GENERAL PRINCIPLES FOR THE RADIOSCOPIC TESTING OF METALLIC MATERIALS BY X- AND GAMMA RAYS
    ISO 11358:1997 Plastics Thermogravimetry (TG) of polymers General principles
    EN ISO 6186:1998 Plastics - Determination of pourability (ISO 6186:1998)
    EN ISO 1628-1:2009/A1:2012 PLASTICS - DETERMINATION OF THE VISCOSITY OF POLYMERS IN DILUTE SOLUTION USING CAPILLARY VISCOMETERS - PART 1: GENERAL PRINCIPLES (ISO 1628-1:2009/AMD 1:2012)
    EN ISO 291:2008 Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008)
    EN 16016-2:2011 Non destructive testing - Radiation methods - Computed tomography - Part 2: Principle, equipment and samples
    DIN EN ISO 11357-1:2016-05 (Draft) PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 1: GENERAL PRINCIPLES (ISO 11357-1:2016)
    DIN EN ISO 1110:1998-03 PLASTICS - POLYAMIDES - ACCELERATED CONDITIONING OF TEST SPECIMENS
    DIN 16742:2013-10 PLASTICS MOULDED PARTS - TOLERANCES AND ACCEPTANCE CONDITIONS
    ISO 1133-2:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
    EN ISO 61:1999 Plastics - Determination of apparent density of moulding material that cannot be poured from a specified funnel (ISO 61:1976)
    ISO 11357-1:2016 Plastics — Differential scanning calorimetry (DSC) — Part 1: General principles
    EN 13068-3:2001 Non-destructive testing - Radioscopic testing - Part 3: General principles of radioscopic testing of metallic materials by X- and gamma rays
    DIN EN ISO 1133-1:2012-03 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
    EN ISO 3274 : 1997 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - NOMINAL CHARACTERISTICS OF CONTACT (STYLUS) INSTRUMENTS
    DIN EN ISO 3167:2014-11 PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014)
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective