• Shopping Cart
    There are no items in your cart

AS 1774.4.1-1990

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Refractories and refractory materials - Physical test methods Preparation of test pieces - Castable refractories

Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

30-06-2017

Superseded by

AS 1774.4.1-2002

Language(s)

English

Published date

01-01-1990

€24.96
Excluding VAT

1 - AS 1774.4.1-1990 REFRACTORIES AND REFRACTORY MATERIALS - PHYSICAL TEST METHODS - PREPARATION OF TEST PIECES - CASTABLE REFRA
1 - PREFACE
1 - CONTENTS
1 - METHOD
1 - 1 SCOPE.
2 - 2 REFERENCED DOCUMENTS.
2 - 3 DEFINITIONS.
2 - 3.1 Cast coverage
2 - 3.2 Dense castable
2 - 3.3 Medi umweight castable
2 - 3.4 Lightweight castable
2 - 3.5 Low- cement castable
2 - 4 PRINCIPLE.
2 - 5 APPARATUS.
2 - 5.1 Mixer
2 - 5.2 Vibrating table
2 - 5.3 Moulds
2 - 5.4 Clamps
2 - 5.5 Drying oven
2 - 5.6 Weighing scale
2 - 5.7 Riffler
2 - 5.8 Thermometer
2 - 5.9 Timing device.
3 - 6 SAMPLING.
3 - 7 PROCEDURE.
3 - 7.1 Sample division.
3 - 7.2 Mixing.
3 - 7.3 Casting of test pieces.
3 - 7.4 Curing and drying.
4 - 5 REPORT.
5 - APPENDIX A - METHOD FOR MEASURING CONSISTENCY OF UNSHAPED CASTABLE REFRACTORIES
5 - A1 SCOPE.
5 - A2 PRINCIPLE.
5 - A3 APPARATUS.
5 - A3.1 Balance
5 - A3.2 Riffler
5 - A3.3 Flow table and mould
5 - A3.4 Callipers
5 - A3.5 Tamper
5 - A3.6 Trowel
5 - A3.7 Castable mixer
5 - A3.8 Thermometer
5 - A4 PROCEDURE.
5 - A4.1 Sample size division.
5 - A4.2 Temperature measurement.
5 - A4.3 Preparation of castable sample.
6 - A4.4 Determination of flow.
6 - A5 REPORT.

Sets out a procedure for laboratory preparation of test pieces from castable refractory materials. A method for measuring consistency is included.

Committee
MN-007
DocumentType
Standard
ISBN
0 7262 6114 9
Pages
6
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes

This Standard describes a procedure for laboratory preparation of test pieces from castable refractory materials.NOTE: The values obtained from test pieces prepared using this method may not correspond with those obtained from test pieces prepared using non-vibratory, or other vibratory, methods. This Standard applies to dense, mediumweight and lightweight castables containing either hydraulic cements or other binders. It does not apply to castable refractories intended primarily for gun application, or to low-cement castables.NOTE: Preparation of test pieces from low-cement castables is covered by AS 1774.4.2.A method for measuring the consistency of unshaped castable refractories is given in Appendix A.

Under Revision see DR 01328 CP

AS 2497.1-2001 Procedures for acceptance testing of refractory products Batch procedure (Reconfirmed 2013)
AS 1774.9-1992 Refractories and refractory materials - Physical test methods Determination of resistance to the disintegrating effect of carbon monoxide
AS 1774.11-1996 Refractories and refractory materials - Physical test methods Thermal expansion
AS 1774.13-2000 Refractories and refractory materials - Physical test methods Permanent dimensional change (Reconfirmed 2013)
AS 2780-1999 Refractories and refractory materials - Glossary of terms
AS 1774.9-2000
AS 1774.27-2001 Refractories and refractory materials - Physical test methods Modulus of rupture at elevated temperatures
AS 1774.1-1991 Refractories and refractory materials - Physical test methods Determination of cold compressive strength
AS 1774.4.2-1992 Refractories and refractory materials - Physical test methods Preparation of test pieces - Low-cement castable refractories
AS 1774.4.3-1998 Refractories and refractory materials - Physical test methods Preparation of test pieces - Unshaped refractories on site
AS 1774.1-2000 Refractories and refractory materials - Physical test methods Determination of cold compressive strength (Reconfirmed 2013)
AS 1774.27-1992 Refractories and refractory materials - Physical test methods Modulus of rupture at elevated temperatures

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.