• There are no items in your cart

AS 1774.4.2-1992

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Refractories and refractory materials - Physical test methods Preparation of test pieces - Low-cement castable refractories

Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

30-06-2017

Superseded by

AS 1774.4.1-2002

Language(s)

English

Published date

01-01-1992

€24.96
Excluding VAT

1 - AS 1774.4.2-1992 REFRACTORIES AND REFRACTORY MATERIALS - PHYSICAL TEST METHODS - PREPARATION OF TEST PIECES - LOW-CEMENT CAS
1 - PREFACE
1 - CONTENTS
1 - METHOD
1 - 1 SCOPE
2 - 2 REFERENCED DOCUMENTS
2 - 3 DEFINITIONS
2 - 3.1 Low-cement castable
2 - 4 PRINCIPLE
2 - 5 SAFETY
2 - 6 APPARATUS
2 - 6.1 Mixer
2 - 6.2 Moulds
2 - 6.3 Immersion vibrator
2 - 6.4 Drying oven
2 - 6.5 Weighing scales
2 - 6.6 Riffle
2 - 6.7 Thermometer
2 - 6.8 Timing device
2 - 7 SAMPLING
2 - 8 PROCEDURE
2 - 8.1 Sample division
2 - 8.2 Mixing
3 - 8.3 Casting of test pieces
3 - 8.4 Curing and drying
3 - 9 REPORT
4 - APPENDIX A - METHOD FOR DETERMINING THE CONSISTENCY OF LOW-CEMENT CASTABLE REFRACTORIES
4 - A1 SCOPE
4 - A2 PRINCIPLE
4 - A3 APPARATUS
4 - A3.1 Balance
4 - A3.2 Riffle
4 - A3.3 Vibrating table
4 - A3.4 Mould
4 - A3.5 Callipers
4 - A3.6 Tamper
4 - A3.7 Trowel
4 - A3.8 Castable mixer
4 - A3.9 Thermometer
4 - A3.10 Timing device
4 - A4 PROCEDURE
4 - A4.1 Sample size division
4 - A4.2 Temperature measurement
4 - A4.3 Preparation of castable sample
4 - A4.4 Determination of flow
5 - A5 REPORT

Describes a procedure for laboratory preparation of test pieces from low-cement castable refractory materials. Does not apply to castable refractories intended primarily for gun manufacture.

Committee
MN-007
DocumentType
Standard
ISBN
0 7262 7171 3
Pages
6
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes

This Standard describes a procedure for laboratory preparation of test pieces from low-cement castable refractory materials.NOTE: The values for physical properties obtained from test pieces prepared using this method may not correspond with those obtained from test pieces prepared using non-vibratory, or other vibratory, methods. Preparation of test pieces from regular castables is covered by AS 1774.4.1, and some low-cement castables have been prepared successfully by that method.This Standard does not apply to castable refractories intended primarily for gun application.This Standard does not apply to free-flowing, low-cement castables, from which test pieces can be prepared by pouring directly into a mould.

First published as AS 1774.4.2-1991.

AS 1141.2-1999 Methods for sampling and testing aggregates Basic testing equipment
AS 2780-1999 Refractories and refractory materials - Glossary of terms
AS 2646.4-1984 Sampling of solid mineral fuels Hard coal - Sampling from stationary situations
AS 1774.4.1-1990 Refractories and refractory materials - Physical test methods Preparation of test pieces - Castable refractories

AS 2497.1-2001 Procedures for acceptance testing of refractory products Batch procedure (Reconfirmed 2013)
AS 1774.11-1996 Refractories and refractory materials - Physical test methods Thermal expansion
AS 1774.13-2000 Refractories and refractory materials - Physical test methods Permanent dimensional change (Reconfirmed 2013)
AS 2780-1999 Refractories and refractory materials - Glossary of terms
AS 1774.29-1995 Refractories and refractory materials - Physical test methods Cast coverage
AS 1774.9-2000
AS 1774.27-2001 Refractories and refractory materials - Physical test methods Modulus of rupture at elevated temperatures
AS 1774.4.3-1998 Refractories and refractory materials - Physical test methods Preparation of test pieces - Unshaped refractories on site
AS 1774.1-2000 Refractories and refractory materials - Physical test methods Determination of cold compressive strength (Reconfirmed 2013)

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.