• AS 2067-2008

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

    Substations and high voltage installations exceeding 1 kV a.c.

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  30-06-2017

    Language(s): 

    Published date:  01-01-2008

    Publisher:  Standards Australia

    Add To Cart

    Abstract - (Show below) - (Hide below)

    Provides minimum requirements for the design and erection of high voltage installations in systems with nominal voltages above 1 kV a.c. and nominal frequency up to and including 60 Hz, so as to provide safety and proper functioning for the use intended.

    Scope - (Show below) - (Hide below)

    This Standard provides minimum requirements for the design and erection of high voltage installations in systems with nominal voltages above 1 kV a.c. and nominal frequency up to and including 60 Hz, so as to provide safety and proper functioning for the use intended.For the purposes of this Standard, a high voltage installation is considered to be:(a) An electricity network substation, under the control of an electricity network operator or entity authorized by a licence or other legal instrument to convey electricity.(b) The high voltage parts of an electrical installation of a power station including all auxiliary systems and interconnecting lines and cables between power stations if on the same site.(c) The high voltage parts of an electrical installation that are not covered in (a) and (b) above. This may include but not be limited to consumer and customer electrical installations serving premises such as factories, commercial facilities, industrial plants, institutional facilities and mine sites.A high voltage installation includes, but is not limited to, the following equipment:(i) High voltage electrical installations on masts, poles and towers.(ii) Switchgear and/or transformers and/or electrical equipment located outside a closed electrical operating area.(iii) Rotating electrical machines.(iv) Switchgear, controlgear and assemblies.(v) Transformers and reactors.(vi) Converters.(vii) Cables.(viii) Lines.(ix) Wiring systems.(x) Batteries, battery chargers and associated d.c. supply systems.(xi) Capacitors.(xii) Earthing systems.(xiii) Buildings and fences that are part of a closed electrical operating area.(xiv) Associated protection, control, auxiliary and ancillary systems.(xv) Structures, foundations, earthworks and drainage.NOTE: In general, a Standard for an item of equipment takes precedence over this Standard.This Standard does not apply to the design and erection of any of the following:(A) Overhead lines and underground cables between separate installations.(B) Ship and offshore installations.(C) Mine site electrical installations, or parts of such installations, for which mining industry specific legislation sets other or additional requirements.(D) Switchgear and/or transformers and/or electrical equipment located within a closed electrical operating area supplied at low voltage and where contact cannot be made with high voltage conductors.(E) Test sites.This Standard does not apply to the design of factory built, type-tested equipment for which separate Australian Standards exist (or IEC standards where Australian standards do not exist) to the extent of requirements covered by the standards. However, all other requirements of this Standard not covered by the type tests for the type-tested equipment must comply with this Standard. In particular, ground safety clearances and section safety clearances must comply with this Standard.Section 11 of this Standard provides additional requirements for the high voltage parts of an electrical installation referred to under (c) above which is not under the control of an electricity network operator or entity authorized by a licence or other legal instrument to convey electricity. NOTES:1 Users of this Standard should be aware of existing local, state or national regulations.2 Further requirements for specific locations may also be referenced or applied through legislation.3 High voltage a.c. installations associated with electric traction systems are included.

    General Product Information - (Show below) - (Hide below)

    Committee EL-043
    Document Type Standard
    Publisher Standards Australia
    Status Superseded
    Superseded By
    Supersedes

    History - (Show below) - (Hide below)

    First published (as AS C13, being endorsement of BS 158:1961 with Australian amendment; AS C52, being endorsement of BS 159:1957 with Australian amendment; and AS C340, being endorsement of BS 162:1962 with Australian amendment) 1967.AS 2067 first published 1977.Fourth edition 2008. First published (as AS C13, being endorsement of BS 158:1961 with Australian amendment; AS C52, being endorsement of BS 159:1957 with Australian amendment; and AS C340, being endorsement of BS 162:1962 with Australian amendment) 1967. AS 2067 first published 1977. Fourth edition 2008.

    Standards Referenced By This Book - (Show below) - (Hide below)

    AS/NZS 1102.111:1997 Graphical symbols forelectrotechnical documentation Architectural and topographical installation plans and diagrams
    AS/NZS 4871.3:2002 Electrical equipment for coal mines, for use underground Substations
    AS 2676.2-1992 Guide to the installation, maintenance, testing and replacement of secondary batteries in buildings - Sealed cells
    AS 60068.2.81-2004 Environmental testing Tests - Test Ei: Shock - Shock response spectrum synthesis
    AS 62271.201-2008 High-voltage switchgear and controlgear AC insulation-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
    AS/NZS 61000.4.16:2002 Electromagnetic compatibility (EMC) Testing and measurement techniques - Test for immunity to conducted common mode disturbances in the frequency range 0 Hz to 150 kHz (Reconfirmed 2013)
    AS/NZS 1680.2.4:1997 Interior lighting Industrial tasks and processes
    AS 60068.2.57-2003 Environmental testing Tests - Test Ff: Vibration - Time-history method
    AS 60038-2000 Standard voltages
    AS 60068.2.66-2003 Environmental testing Tests - Test Cx: Damp heat, steady state (unsaturated pressurized vapour)
    AS/NZS 60479.1:2002 Effects of current on human beings and livestock General aspects
    AS 60068.2.13-2003 Environmental testing Tests - Test M: Low air pressure
    AS/NZS 61000.4.2:2002 Electromagnetic compatibility (EMC) Testing and measurement techniques - Electrostatic discharge immunity test
    AS/NZS 61000.6.2:2006 Electromagnetic compatibility (EMC) General standards - Immunity for industrial environments (Reconfirmed 2016)
    AS/NZS 1680.0:1998 Interior lighting - Safe movement
    AS/NZS 61000.4.34:2007 Electromagnetic compatibility (EMC) Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests for equipment with input current more than 16 A per phase (IEC 61000-4-34, Ed. 1.0 (2005) MOD)
    AS/NZS 1768:2007 Lightning protection
    AS 60068.2.7-2003 Environmental testing Tests - Test Ga and guidance: Acceleration, steady state
    AS 60068.3.8-2004 Environmental testing - Supporting documentation and guidance - Selecting amongst vibration tests
    AS 60068.2.54-2004 Environmental testing Tests - Test Ta: Soldering - Solderability testing by the wetting balance method
    AS 60068.2.61-2003 Environmental testing Tests - Test Z/ABDM: Climate sequence
    AS 60068.2.59-2003 Environmental testing Tests - Test Fe: Vibration - Sine beat method
    AS 60068.2.69-2004 Environmental testing Tests - Test Te: Soldering - Solderability testing of electronic components for surface mount technology by the wetting balance method
    AS 60068.2.14-2003 Environmental testing Tests - Test N: Change of temperature
    AS 3735-2001 Concrete structures for retaining liquids
    AS 60068.2.44-2004 Environmental testing Tests - Guidance on test T: Soldering
    AS/NZS 61000.4.30:2007 Electromagnetic compatibility (EMC) Testing and measurement techniques - Power quality measurement methods
    AS 62271.203-2005 High-voltage switchgear and controlgear Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV (IEC 62271-203, Ed. 1.0 (2003) MOD)
    AS 60068.4-2003 Environmental testing - Information for specification writers - Test summaries
    AS 1824.1-1995 Insulation co-ordination Definitions, principles and rules
    AS 3865-1991 Calculation of the effects of short-circuit currents
    AS/NZS 4360:2004 Risk management
    AS/NZS 61000.6.4:2007 Electromagnetic compatibility (EMC) Generic standards - Emission standard for industrial environments
    AS/NZS 61000.6.1:2006 Electromagnetic compatibility (EMC) Generic standards - Immunity for residential, commercial and light industrial environments (Reconfirmed 2016)
    AS 60068.2.27-2003 Environmental testing Tests - Test Ea and guidance: Shock
    HB 102-1997 (CJC 6) Coordination of power and telecommunications - Low Frequency Induction (LFI) - Application Guide to the LFI Code
    AS 62271.200-2005 High-voltage switchgear and controlgear A.C. metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV (IEC 62271-200, Ed. 1 (2003) MOD)
    AS/NZS 4871.4:2002 Electrical equipment for coal mines, for use underground Mains powered electrical mobile machines
    AS 1931.1-1996 High-voltage test techniques - General definitions and test requirements
    AS 3735 SUPP 1-2001 Concrete structures for retaining liquids - Commentary (Supplement to
    AS 1824.2-1985 Insulation coordination (phase-to-earth and phase-to-phase, above 1 kV) - Application guide
    AS/NZS 61000.2.12:2003 Electromagnetic compatibility (EMC) Environment - Compatibility levels for low-frequency conducted disturbances and signalling in public medium-voltage power supply systems (Reconfirmed 2013)
    AS/NZS 3008.1.1:1998 Electrical installations - Selection of cables - Cables for alternating voltages up to and including 0.6/1 kV - Typical Australian installation conditions
    AS 60068.2.60-2003 Environmental testing Tests - Test Ke: Flowing mixed gas corrosion test
    AS/NZS 1170.1:2002 Structural design actions Permanent, imposed and other actions
    AS 1682.2-1990 Fire Dampers Installation
    AS 4100 SUPP 1-1999 Steel structures - Commentary (Supplement to AS 4100-1998)
    AS/NZS 4383.4:1998 Preparation of documents used in electrotechnology Location and installation documents
    AS 60068.2.48-2003 Environmental testing Tests - Guidance on the application of the tests of AS 60068 to simulate the effects of storage
    AS 1359.101-1997 Rotating electrical machines - General requirements - Rating and performance
    AS/NZS 61000.4.8:2002 Electromagnetic compatibility (EMC) Testing and measurement techniques - Power frequency magnetic field immunity test
    AS 60068.2.43-2004 Environmental testing Tests - Test Kd: Hydrogen sulphide test for contacts and connections
    AS 60068.2.38-2003 Environmental testing Tests - Test Z/AD: Composite temperature/humidity cyclic test
    AS 60068.2.20-2004 Environmental testing Tests - Test T: Soldering
    AS 1100.401-1984 Technical drawing Engineering survey and engineering survey design drawing
    AS 60068.2.6-2003 Environmental testing Tests - Test Fc: Vibration (sinusoidal) (Reconfirmed 2018)
    AS 1170.4-2007 Structural design actions Earthquake actions in Australia (Reconfirmed 2018)
    AS 60068.3.6-2003 Environmental testing - Supporting documentation and guidance - Confirmation of the performance of temperature/humidity chambers
    AS 1100.301-2008 Technical drawing Architectural drawing (Reconfirmed 2018)
    AS 60068.2.47-2003 Environmental testing Tests - Mounting of compounds, equipment and other articles for vibration, impact and similar dynamic tests
    AS/NZS 3100:2002 Approval and test specification - General requirements for electrical equipment
    AS/NZS 61000.4.14:2007 Electromagnetic compatibility (EMC) Testing and measurement techniques - Voltage fluctuation immunity test
    AS/NZS 61000.3.3:2006 Electromagnetic compatibility (EMC) - Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current per phase and not subject to conditional connection
    AS 60068.2.64-2003 Environmental testing Tests - Test Fh: Vibration, broad-band random (digital control) and guidance
    AS 4100-1998 Steel structures (Reconfirmed 2016)
    AS/NZS 61000.3.4:2007 Electromagnetic compatibility (EMC) Limits - Limitation of emission of harmonic currents in low-voltage power supply systems for equipment with rated current greater than 75 A (Reconfirmed 2018)
    AS 60068.3.5-2003 Environmental testing - Supporting documentation and guidance - Confirmation of the performance of temperature chambers
    AS/NZS 61000.4.11:2005 Electromagnetic compatibility (EMC) Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests (IEC 61000-4-11, Ed. 2.0 (2004) MOD) (Reconfirmed 2016)
    HB 242-2007 High voltage mining equipment for use underground (Reconfirmed 2019)
    AS/NZS 4383.3:1996 Preparation of documents used in electrotechnology Connection diagrams, tables and lists
    AS/NZS 1680.1:2006 Interior and workplace lighting General principles and recommendations
    AS 1210 SUPP 2-1999 Pressure vessels - Cold-stretched austenitic stainless steel vessels (Supplement to AS 1210-1997)
    AS/NZS 61000.2.3:1999 Electromagnetic compatibility (EMC) Environment - Description of the environment - Radiated and non-network-frequency-related conducted phenomena (Reconfirmed 2016)
    AS 1210 SUPP 1-1990 Unfired Pressure Vessels - Advanced design and construction (Supplement to AS 1210-1997)
    AS 1210-1997 Pressure vessels
    AS/NZS 61000.1.1:2000 Electromagnetic compatibility (EMC) General - Application and interpretation of fundamental definitions and terms (Reconfirmed 2016)
    AS 60068.2.58-2004 Environmental testing Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD)
    AS 60068.2.78-2003 Environmental testing Tests - Test Cab: Damp heat, steady state (Reconfirmed 2018)
    AS/NZS 3835.2:2006 Earth potential rise - Protection of telecommunications network users, personnel and plant Application guide
    AS 60068.5.2-2003 Environmental testing - Guide to drafting of test methods - Terms and definitions
    AS/NZS 61000.4.3:2006 Electromagnetic compatibility (EMC) Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
    AS 60068.2.11-2003 Environmental testing Tests - Test Ka: Salt mist
    AS 60068.2.30-2003 Environmental testing Tests - Test Db and guidance: Damp heat, cyclic (12 + 12-hour cycle)
    AS 60068.2.2-2003 Environmental testing Tests - Test B: Dry heat (Reconfirmed 2018)
    AS 60068.2.40-2003 Environmental testing Tests - Test Z/AM: Combined cold/low air pressure tests
    AS 60068.3.2-2003 Environmental testing - Background information - Combined temperature/low air pressure tests
    AS 60068.2.68-2003 Environmental testing Tests - Test L: Dust and sand
    AS 60068.2.10-2003 Environmental testing Tests - Test J and guidance: Mould growth
    AS 60068.2.52-2003 Environmental testing Tests - Test Kb: Salt mist, cyclic (sodium chloride solution)
    AS/NZS 4871.1:2002 Electrical equipment for coal mines, for use underground General requirements
    AS/NZS 61000.3.6:2001 Electromagnetic compatibility (EMC) Limits - Assessment of emission limits for distorting loads in MV and HV power systems (IEC 61000-3-6:1996, MOD)
    AS 60068.2.21-2004 Environmental testing Tests - Test U: Robustness of terminations and integral mounting devices
    AS 60068.2.55-2003 Environmental testing - Tests - Test Ee and guidance: Bounce
    AS/NZS 1680.2.3:2008 Interior and workplace lighting Specific applications - Educational and training facilities
    AS/NZS 3008.1.2:1998 Electrical installations - Selection of cables - Cables for alternating voltages up to and including 0.6/1 kV - Typical New Zealand installation conditions
    AS 1170.4 SUPP 1-1993 Minimum design loads on structures (known as the SAA Loading Code) Earthquake loads - Commentary (Supplement to AS 1170.4-1993)
    AS 60068.2.39-2003 Environmental testing Tests - Test Z/AMD: Combined sequential cold, low air pressure and damp heat test
    AS 60068.2.18-2003 Environmental testing Tests - Test R and guidance: Water
    AS 60068.2.70-2003 Environmental testing Tests - Test Xb: Abrasion of markings and letterings caused by rubbing of fingers and hands
    AS/NZS 61000.4.7:2007 Electromagnetic compatibility (EMC) Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto
    AS/NZS 3013:2005 Electrical installations - Classification of the fire and mechanical performance of wiring system elements (Reconfirmed 2020)
    AS/NZS 60079.0:2008 Explosive atmospheres Equipment - General requirements
    AS 60068.2.32-2003 Environmental testing Tests - Test Ed: Free fall
    AS/NZS 1680.2.1:2008 Interior and workplace lighting Specific applications - Circulation spaces and other general areas
    AS 60068.2.5-2003 Environmental testing Tests - Test Sa: Simulated solar radiation at ground level
    AS/NZS 3835.1:2006 Earth potential rise - Protection of telecommunications network users, personnel and plant Code of practice
    AS 2374.6-1994 Power transformers - Determination of transformer and reactor sound levels
    AS/NZS 4871.2:2002 Electrical equipment for coal mines, for use underground Distribution, control and auxiliary equipment
    AS 60068.2.46-2004 Environmental testing Tests - Guidance to test Kd: Hydrogen sulphide test for contacts and connections
    AS 60068.2.29-2003 Environmental testing Tests - Test Eb and guidance: Bump
    AS/NZS 61000.4.1:2006 Electromagnetic compatibility (EMC) Testing and measurement techniques - Overview of IEC 61000-4 series
    AS/NZS 61000.4.13:2006 Electromagnetic compatibility (EMC) - Testing and measurement techniques - Harmonics and interharmonics including mains signalling at a.c. power port, low frequency immunity tests
    HB 100-2000 (CJC 4) COORDINATION OF POWER AND TELECOMMUNICATIONS - Manual for the establishment of safe work practices and the minimization of operational interference between power systems and paired cable telecommunications systems
    AS 60068.2.74-2003 Environmental testing Tests - Test Xc: Fluid contamination
    AS 60068.2.75-2003 Environmental testing Tests - Test Eh: Hammer tests
    AS/NZS 1170.2:2002 Structural design actions Wind actions
    AS/NZS 61000.3.7:2001 Electromagnetic compatibility (EMC) Limits - Assessment of emission limits for fluctuating loads in MV and HV power systems (IEC 61000-3-7:1996, MOD)
    AS 60068.1-2003 Environmental testing General and guidance (Reconfirmed 2018)
    AS 62271.202-2008 High-voltage switchgear and controlgear High-voltage/low-voltage prefabricated substation
    AS/NZS 1680.2.2:2008 Interior and workplace lighting Specific applications - Office and screen-based tasks
    AS 2791-1996 High-voltage switchgear and controlgear - Use and handling of sulphur hexafluoride (SF6) in high-voltage switchgear and controlgear
    AS 3700 SUPP 1-2004 Masonry structures - Commentary (Supplement to AS 3700-2001)
    AS/NZS 61000.4.5:2006 Electromagnetic compatibility (EMC) Testing and measurement techniques - Surge immunity test
    AS 60068.2.31-2003 Environmental testing Tests - Test Ec: Drop and topple, primarily for equipment-type specimens
    AS 1055.1-1997 Acoustics - Description and measurement of environmental noise - General procedures
    AS/NZS 61000.4.6:2006 Electromagnetic compatibility (EMC) Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields
    AS 3600 SUPP 1-1994 Concrete structures - Commentary (Supplement to AS 3600-1994)
    AS 3851-1991 The calculation of short-circuit currents in three-phase a.c. systems (Reconfirmed 2015)
    AS 3011.1-1992 Electrical installations - Secondary batteries installed in buildings - Vented cells Vented cells
    AS 60076.11-2006 Power transformers Dry-type transformers
    AS/NZS 1170.0:2002 Structural design actions General principles
    AS 60068.3.1A-2003 Environmental testing Background information - Section one: Cold and dry heat tests - First supplement
    AS/NZS 61000.4.15:2005 Electromagnetic compatibility (EMC) Testing and measurement techniques - Flickermeter - Function and design specifications
    AS/NZS 61000.6.3:2007 Electromagnetic compatibility (EMC) Generic standards - Emission standard for residential, commercial and light-industrial environments
    AS 1100.101-1992 Technical drawing General principles
    AS 3600-2001 Concrete structures
    AS 1940-2004 The storage and handling of flammable and combustible liquids
    AS 2650-2005 Common specifications for high-voltage switchgear and controlgear standards (IEC 60694 Ed.2.2(2002) MOD)
    AS 1905.1-2005 Components for the protection of openings in fire-resistant walls Fire-resistant doorsets
    AS 60068.2.1-2003 Environmental testing Tests - Test A: Cold (Reconfirmed 2018)
    AS 60068.2.67-2003 Environmental testing Tests - Test Cy: Damp heat, steady state accelerated test primarily intended for components
    AS/NZS 61000.4.27:2006 Electromagnetic compatibility (EMC) - Testing and measurement techniques - Unbalance, immunity test
    HB 103-1997 (CJC 7) Coordination of power and telecommunications - Crossings code - The arrangement of overhead power and telecommunications lines, pole stay wires, and suspension wires
    AS/NZS 2344:1997 Limits of electromagnetic interference from overhead a.c. powerlines and high voltage equipment installations in the frequency range 0.15 to 1000 MHz
    AS 1682.1-1990 Fire dampers Specification
    AS/NZS 61000.3.11:2002 Electromagnetic compatibility (EMC) Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems - Equipment with rated current less than or equal to 75 A and subject to conditional connection (Reconfirmed 2013)
    AS 60068.2.50-2003 Environmental testing Tests - Test Z/Afc: Combined cold/vibration (sinusoidal) tests for both heat-dissipating and non-heat-dissipating specimens
    AS/NZS 61000.4.4:2006 Electromagnetic compatibility (EMC) Testing and measurement techniques - Electrical fast transient/burst immunity test
    AS 60529-2004 Degrees of protection provided by enclosures (IP Code) (Reconfirmed 2018)
    AS 1319-1994 Safety signs for the occupational environment (Reconfirmed 2018)
    AS 60068.2.9-2003 Environmental testing Tests - Guidance for solar radiation testing
    AS 2293.3-2005 Emergency escape lighting and exit signs for buildings - Emergency escape luminaires and exit signs
    HB 219:2006 Earth potential rise - Protection of telecommunications network users, personnel and plant - Worked examples for the application guide (Reconfirmed 2020)
    AS/NZS 61000.3.12:2006 Electromagnetic compatibility (EMC) Limits - Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current greater than 16 A and less than or equal to 75 A per phase
    HB 101-1997 (CJC 5) Coordination of power and telecommunications - Low Frequency Induction (LFI) - Code of practice for the mitigation of hazardous voltages induced into telecommunications lines
    AS 60068.2.42-2004 Environmental testing Tests - Test Kc: Sulphur dioxide test for contacts and connections (Reconfirmed 2018)
    AS/NZS 61000.3.5:1998 Electromagnetic compatibility (EMC) Limits - Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16 A
    AS/NZS 1668.1:1998 The use of ventilation and airconditioning in buildings Fire and smoke control in multi-compartment buildings
    AS/NZS 1680.4:2001 Interior lighting - Maintenance of electric lighting systems
    AS 60068.2.41-2003 Environmental testing Tests - Test Z/BM: Combined dry heat/low air pressure tests
    AS 2676.1-1992 Guide to the installation, maintenance, testing and replacement of secondary batteries in buildings - Vented cells
    AS/NZS 61000.2.5:1999 Electromagnetic compatibility (EMC) Environment - Classification of electromagnetic environments (Reconfirmed 2016)
    AS/NZS 4383.1:1996 Preparation of documents used in electrotechnology General requirements
    AS 3700-2001 Masonry structures
    AS/NZS 2865:2001 Safe working in a confined space
    AS 60068.2.45-2003 Environmental testing Tests - Test XA and guidance: Immersion in cleaning solvents
    AS 60068.3.7-2003 Environmental testing - Supporting documentation and guidance - Measurements in temperature chambers for tests A and B (with load)
    AS/NZS 61000.2.2:2003 Electromagnetic compatibility (EMC) Environment - Compatibility levels for low-frequency conducted disturbances and signalling in public low-voltage power supply systems (Reconfirmed 2013)
    AS/NZS 61000.3.2:2007 Electromagnetic compatibility (EMC) Limits - Limits for harmonic current emissions (equipment input current (16 A per phase) (IEC 61000-3-2, Ed. 3.0 (2005) MOD)
    AS 60068.2.77-2004 Environmental testing Tests - Test 77: Body strength and impact shock
    AS 4436-1996 Guide for the selection of insulators in respect of polluted conditions
    AS/NZS 4383.2:1996 Preparation of documents used in electrotechnology Function-oriented diagrams
    AS 60068.2.17-2003 Environmental testing Tests - Test Q: Sealing
    AS/NZS 4871.6:2007 Electrical equipment for coal mines, for use underground Diesel powered machinery and ancillary equipment
    AS 3011.2-1992 Electrical installations - Secondary batteries installed in buildings Sealed cells
    AS/NZS 4871.5:2002 Electrical equipment for coal mines, for use underground Battery powered electrical mobile machines
    AS/NZS 1680.2.5:1997 Interior lighting - Hospital and medical tasks
    AS 60068.2.65-2003 Environmental testing Tests - Test Fg: Vibration, acoustically induced
    AS 60068.3.4-2003 Environmental testing Supporting documentation and guidance - Damp heat tests
    AS 2444-2001 Portable fire extinguishers and fire blankets - Selection and location (Reconfirmed 2021)
    AS/NZS 3000:2007 Electrical installations (known as the Australian/New Zealand Wiring Rules)
    AS 60068.3.1-2003 Environmental testing Background information - Section one: Cold and dry heat tests
    AS 60068.3.3-2003 Environmental testing - Guidance - Seismic test methods for equipment
    AS 1100.201-1992 Technical drawing Mechanical engineering drawing
    AS 60068.2.33-2003 Environmental testing Tests - Guidance on change of temperature tests
    AS 60068.2.53-2003 Environmental testing Tests - Guidance to tests Z/AFc and Z/BFc: Combined temperature (cold and dry heat) and vibration (sinusoidal) tests
    AS 2374.2-1997 Power transformers Temperature rise
    AS 60068.2.51-2003 Environmental testing Tests - Test Z/BFc: Combined dry heat/vibration (sinusoidal) tests for both heat-dissipating and non-heat-dissipating specimens
    AS 60068.2.49-2004 Environmental testing Tests - Guidance to Test Kc: Sulphur dioxide test for contacts and connections

    Standards Referencing This Book - (Show below) - (Hide below)

    AS/NZS 3800:2012 Electrical equipment for explosive atmospheres - Repair and overhaul
    AS 5062:2016 Fire protection for mobile and transportable equipment
    AS/NZS 4871.2:2010 Electrical equipment for mines and quarries Distribution, control and auxiliary equipment
    AS/NZS 7000:2016 Overhead line design
    AS/NZS 4871.1:2010 Electrical equipment for mines and quarries General requirements
    AS/NZS 4871.6:2013 Electrical equipment for mines and quarries Diesel powered machinery and ancillary equipment
    AS/NZS 1418.10:2011 Cranes, hoists and winches Mobile elevating work platforms
    HB 331-2012 Overhead line design
    AS/NZS 5601.1:2013 Gas installations General installations
    AS/NZS 7000:2010 Overhead line design - Detailed procedures
    AS/NZS 4871.1:2012 Electrical equipment for mines and quarries General requirements
    AS/NZS 3007:2013 Electrical equipment in mines and quarries - Surface installations and associated processing plant
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective