AS 2439.2-1983

1 - AS 2439 Part 2-1983 PERFORATED PLASTICS DRAINAGE AND EFFLUENT PIPE AND FITTINGS - PERFORATED EFFLUENT PIPE AND ASSOCIATED FIT
4 - PREFACE
5 - CONTENTS
6 - 1 SCOPE.
6 - 2 REFERENCED DOCUMENTS.
6 - 3 TYPES AND CLASSIFICATION.
6 - 3.1 Types.
6 - 3.2 Classification.
6 - 4 MATERIAL.
6 - 5 FREEDOM FROM DEFECTS.
6 - 6 DIMENSIONS.
6 - 6.1 Diameter.
7 - 6.2 Length.
7 - 6.3 Wall Thickness.
7 - 7 PERFORATIONS.
7 - 7.1 Type 3 Pipe.
7 - 7.2 Type 4 Pipe.
7 - 8 FITTINGS.
7 - 9 PACKAGING.
7 - 10 CONDITIONING OF TEST SPECIMENS.
7 - 11 PERFORMANCE REQUIREMENTS.
7 - 11.1 Bending (Applicable to Type 3 only).
7 - 11.2 Straightening (Applicable to Type 3 only).
7 - 11.3 High Temperature Impact Resistance.
7 - 11.4 Low Temperature Impact Resistance.
7 - 11.5 Elongation (Applicable to Type 3 only).
7 - 11.6 Pipe Stiffness.
8 - 11.7 Perforation Deformation.
8 - 11.8 Joint Separation (Applicable to Type 3 only).
8 - 12 MARKING.
8 - 12.1 Type 3.
8 - 12.2 Type 4.
9 - APPENDIX A - DETERMINATION OF COMPLIANCE OF A LOT
9 - INTRODUCTION.
9 - A1 AUSTRALIAN STANDARDS MARK.
9 - A2 ASSESSMENT OF COMPLIANCE ON THE BASIS OF STATISTICAL SAMPLING
9 - A3 ASSURANCE OF COMPLIANCE ON THE BASIS OF SUPPLIERS’ QUALITY CONTROL SYSTEMS
10 - APPENDIX B - METHODS FOR MEASUREMENT OF DIMENSIONS
10 - B1 SCOPE.
10 - B2 APPARATUS.
10 - B3 PREPARATION OF TEST SPECIMENS
10 - B3.1 Diameter-Outside and Inside.
10 - B3.2 Length.
10 - B3.3 Perforations.
10 - B4 TEST PROCEDURE.
11 - B5 REPORT.
11 - B5.1 Outside Diameter.
11 - B5.2 Inside Diameter.
11 - B5.3 Length.
11 - B5.4 Perforations.
12 - APPENDIX C - BENDING TEST (TYPE 3 ONLY)
12 - C1 SCOPE.
12 - C2 PRINCIPLE.
12 - C3 APPARATUS.
12 - C4 PREPARATION OF TEST SPECIMENS.
12 - C5 TEST PROCEDURE.
12 - C6 REPORT.
13 - APPENDIX D - STRAIGHTENING TEST AT 0° C (TYPE 3 ONLY)
13 - D1 SCOPE.
13 - D2 PRINCIPLE.
13 - D3 APPARATUS.
13 - D4 PREPARATION OF TEST SPECIMENS.
13 - D5 TEST PROCEDURE.
13 - D6 REPORT.
14 - APPENDIX E - METHOD OF TEST FOR HIGH TEMPERATURE IMPACT RESISTANCE
14 - E1 SCOPE.
14 - E2 PRINCIPLE.
14 - E3 APPARATUS.
14 - E4 PREPARATION OF TEST SPECIMENS.
14 - E5 TEST PROCEDURE.
14 - E6 REPORT.
15 - APPENDIX F - METHOD OF TEST FOR LOW TEMPERATURE IMPACT RESISTANCE
15 - F1 SCOPE.
15 - F2 PRINCIPLE.
15 - F3 APPARATUS.
15 - F4 PREPARATION OF TEST SPECIMENS.
15 - F5 TEST PROCEDURE.
15 - F6 REPORT.
16 - APPENDIX G - METHOD FOR DETERMINING ELONGATION AND PERFORATION DEFORMATION (TYPE 3 ONLY)
16 - G1 SCOPE.
16 - G2 PRINCIPLE.
16 - G3 APPARATUS.
16 - G4 PREPARATION OF TEST SPECIMENS.
16 - G5 TEST PROCEDURE.
16 - G6 CALCULATION.
16 - G7 REPORT.
16 - G7.1 Pipe Elongation.
16 - G7.2 Perforation Deformation.
17 - APPENDIX H - METHOD FOR DETERMINING PIPE STIFFNESS AND PERFORATION DEFORMATION
17 - H1 SCOPE.
17 - H2 PRINCIPLE.
17 - H3 APPARATUS.
17 - H4 PREPARATION OF TEST SPECIMENS.
17 - H5 TEST PROCEDURE.
18 - H6 CALCULATIONS.
18 - H7 REPORT.
18 - H7.1 Pipe Stiffness.
18 - H7.2 Perforation Deformation (Type 4 only).
18 - APPENDIX J - METHOD OF TEST FOR JOINT SEPARATION (TYPE 3 ONLY)
18 - J1 SCOPE.
18 - J2 PRINCIPLE.
18 - J3 APPARATUS.
18 - J4 PREPARATION OF TEST SPECIMEN.
18 - J5 TEST PROCEDURE.
18 - J6 REPORT.

Covers smooth wall and corrugated effluent pipe and fittings intended for effluent disposal from septic sewerage systems. Test requirements for bending, straightening, high and low temperature impact resistance, elongation, pipe stiffness, perforation deformation and joint separation are given.

This standard specifies requirements for perforated plastics effluent pipe and associated fittings intended for effluent disposal from septic sewerage systems.NOTE: Advisory information on the determination of compliance of a 'lot' with this standard is given in Appendix A.