• Shopping Cart
    There are no items in your cart

AS 4032.2-2002

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Water supply - Valves for the control of hot water supply temperatures - Tempering valves and end of line temperature actuated devices

Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

25-07-2024

Superseded by

AS 4032.2-2005

Language(s)

English

Published date

01-01-2002

€77.79
Excluding VAT

1 - AS 4032.2:2002 WATER SUPPLY - VALVES FOR THE CONTROL OF HOT WATER SUPPLY TEMPERATURES - TEMPERING VALVES AND END-OF-LINE ...
4 - PREFACE
5 - CONTENTS
7 - FOREWORD
8 - SECTION 1 - SCOPE AND GENERAL
8 - 1.1 SCOPE
8 - 1.2 REFERENCED DOCUMENTS
9 - 1.3 DEFINITIONS
9 - 1.3.1 Distortion
9 - 1.3.2 Manufacturer’s recommended commissioning temperature
9 - 1.3.3 Steady mixed water discharge temperature
9 - 1.3.4 Transient mixed water discharge temperatures
9 - 1.4 INSTRUMENTATION
9 - 1.5 TOLERANCES
9 - 1.6 MARKING
11 - SECTION 2 - MATERIALS
11 - 2.1 GENERAL
11 - 2.2 COPPER ALLOY MATERIALS
11 - 2.3 DIAPHRAGM MATERIALS AND VALVE SEATS
11 - 2.4 SPRING MATERIALS
11 - 2.5 CONTAMINATION OF WATER
12 - SECTION 3 - DESIGN AND CONSTRUCTION
12 - 3.1 GENERAL
12 - 3.2 STRENGTH
12 - 3.2.1 Torque test
12 - 3.2.2 Leakage
12 - 3.3 END CONNECTIONS
12 - 3.4 COMPONENTS AND VALVE SEATS
12 - 3.5 REPAIR
12 - 3.6 INSTRUCTIONS
13 - SECTION 4 - TEMPERING VALVE
13 - 4.1 GENERAL
13 - 4.2 INLET AND OUTLET CONNECTIONS
13 - 4.3 DESIGN REQUIREMENTS
13 - 4.4 TEMPERATURE STABILITY OF MIXED WATER
14 - 4.5 SEQUENCE OF TESTS
15 - 4.6 ENDURANCE OF THERMOSTATIC ELEMENT AND OPERATING MECHANISM
15 - 4.7 MARKING
15 - 4.8 MANUFACTURER’S INSTRUCTIONS
16 - SECTION 5 - END-OF-LINE TEMPERATURE-ACTUATED FLOW DEVICES
16 - 5.1 GENERAL
16 - 5.2 CONNECTIONS
16 - 5.3 ACTUATING TEMPERATURE
16 - 5.4 PERFORMANCE
16 - 5.4.1 Flow rate
16 - 5.4.2 Response
16 - 5.5 ENDURANCE
16 - 5.6 MARKING
17 - 5.7 MANUFACTURER’S INSTRUCTIONS
18 - APPENDIX A - INSTRUMENTATION
18 - A2 GENERAL
18 - A3 FLOWMETER (for use with air)
18 - A4 FLOWMETER (for use with water)
18 - A5 PRESSURE GAUGES (for use with water)
18 - A6 TEMPERATURE-INDICATING AND RECORDING DEVICES
18 - A7 STOPWATCH
18 - A8 TORQUE APPLICATOR
19 - APPENDIX B - TORQUE TEST
19 - B1 SCOPE
19 - B2 PRINCIPLE
19 - B3 APPARATUS
19 - B4 PROCEDURE
20 - B5 TEST REPORT
21 - APPENDIX C - LEAKAGE TEST
21 - C1 SCOPE
21 - C2 PRINCIPLE
21 - C3 APPARATUS
21 - C4 PROCEDURE
21 - C5 REPORT
22 - APPENDIX D - INFORMATION ON SCALDS FROM HOT WATER
23 - APPENDIX E - TEMPERATURE STABILITY OF MIXED WATER TEST - TEMPERING VALVES
23 - E1 SCOPE
23 - E2 PRINCIPLE
23 - E3 APPARATUS
24 - E4 PRESSURE DROP, TEMPERATURE VARIATION AND OUTLET FLOW VARIATION PROCEDURE
25 - E5 THERMAL SHUT-OFF
26 - E6 MIXED WATER TEMPERATURE OVERSHOOT ON STARTING FROM AMBIENT
27 - E7 REPORT
33 - APPENDIX F - ENDURANCE TEST - TEMPERING VALVES
33 - F1 SCOPE
33 - F2 PRINCIPLE
33 - F3 APPARATUS
33 - F4 PROCEDURE
34 - F5 REPORT
35 - APPENDIX G - PERFORMANCE AND ENDURANCE TESTS - END-OF-LINE TEMPERATURE-ACTUATED FLOW DEVICES
35 - G1 SCOPE
35 - G2 PRINCIPLE
35 - G3 APPARATUS
36 - G4 PROCEDURE (see Figure G1)
37 - G5 REPORT

Specifies requirements for the design, construction, testing and performance of tempering valves of nominal sizes not larger than DN 32 and end-of-line temperature-actuated devices of nominal size DN 15, for use with hot water at a supply temperature not exceeding 99 degrees Celsius, and hot and cold water with continuous working pressures not exceeding 1400 kPa.

Committee
WS-026
DocumentType
Standard
ISBN
0 7337 4037 5
Pages
30
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

This Standard specifies requirements for the design, construction, testing and performanceof(a) tempering valves of nominal sizes not larger than DN 32; and(b) end-of-line temperature-actuated devices of nominal size DN 15, for use with hot water at(i) continuous operating temperature not exceeding 85C;(ii) temperature under emergency conditions, not exceeding 99C; and(iii) continuous working pressure not exceeding 1400 kPa.The major requirement of the testing procedures is that the device under test does not permit the continuous discharge of water from the outlet in excess of 50C.Discharges of water with a temperature in excess of this figure, which comply with the specified cumulative time/temperature factors, are acceptable.

First published as AS 4032.3-2002.

AS 1432-1996 Copper tubes for plumbing, gasfitting and drainage applications
AS 1722.1-1975 Pipe threads of Whitworth form Sealing pipe threads (metric units)
AS 2837-1986 Wrought alloy steels - Stainless steel bars and semi-finished products
AS 2345-1992 Dezincification resistance of copper alloys
AS 1349-1986 Bourdon tube pressure and vacuum gauges (Reconfirmed 2018)
AS 3688-1994 Water supply - Copper and copper alloy body compression and capillary fittings and threaded-end connectors
AS/NZS 4020:1999 Products for use in contact with drinking water
AS 1722.2-1992 Pipe threads of Whitworth form Fastening pipe threads (Reconfirmed 2017)

ATS 5200.453-2004 Technical Specification for plumbing and drainage products Heated water systems - Thermostatic circulation valve
ATS 5200.468-2005 Technical Specification for plumbing and drainage products Hot water systems - Recirculation valves
AS/NZS 3500.4:2003 Plumbing and drainage Heated water services
MP 52-2005 Manual of authorization procedures for plumbing and drainage products
AS 5200.000-2005 Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products
AS 4032.3-2004 Water supply - Valves for the control of heated water supply temperatures Requirements for field-testing, maintenance or replacement of thermostatic mixing valves, tempering valves and end-of-line temperature control devices
AS 3498-2003 Authorization requirements for plumbing products - Water heaters and hot-water storage tanks

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.