AS 4441(INT)-2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Oriented PVC (PVC-O) pipes for pressure applications
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
29-05-2024
English
13-05-2004
This Interim Australian Standard specifies the general aspects of pipes and joints made of oriented unplasticized poly (vinyl chloride) (PVC-O), for piping systems intended to be used underground and above ground where not exposed to direct sunlight, for water mains and services, pressurized sewer systems and irrigation systems.
CommentClosesDate |
23-05-2005
|
Committee |
PL-021
|
DocumentType |
Standard
|
ISBN |
0 7337 5185 7
|
Pages |
33
|
PublisherName |
Standards Australia
|
Status |
Superseded
|
SupersededBy | |
Supersedes | |
UnderRevision |
This Interim Australian Standard specifies the general aspects of pipes and joints made oforiented unplasticized poly (vinyl chloride)(PVC-O),for piping systems intended to be used underground and above ground where not exposed to direct sunlight,for water mains and services, pressurized sewer systems and irrigation systems.The piping system according to this Standard is intended for the conveyance of cold water under pressure up to 40 °C for drinking water and for general purposes up to and including 45°C, and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations,up to pressure ratings of 25 bar.Joints constructed of other materials shall meet their own relevant standards in addition tothe fitness for purpose requirements in this Standard.NOTE: Means for demonstrating compliance with this Standard are given in Appendix A. Pipesintended for drinking water are required to conform to the cold water requirements ofAS/NZS 4020. The validity of compliance is limited to 40°C, and it is a recommendation of theWater Services Association of Australia that temperatures of water supply systems be limited tothis value.
First published as AS/NZS 4441(Int):1996.
Revised and designated as AS 4441(Int)-2003.
AS/NZS 1462.1:2001 | Methods of test for plastics pipes and fittings Method for determining the dimensions of pipes and fittings |
HB 18.28-1991 | Guidelines for third-party certification and accreditation - Guide 28: General rules for a model third-party certification system for products |
AS/NZS 1462.22:1997 | Methods of test for plastics pipes and fittings Method for determination of pipe stiffness |
AS/NZS 1462.1:2006 | Methods of test for plastics pipes and fittings Method for determining the dimensions of pipes and fittings (Reconfirmed 2024) |
AS 1199-1988 | Sampling procedures and tables for inspection by attributes |
HB 18.28-2005 | Conformity assessment - Guidance on a third-party certification system for products |
AS/NZS 4020:2005 | Testing of products for use in contact with drinking water |
AS/NZS 1462.6:1998 | Methods of test for plastics pipes and fittings - Method for hydrostatic pressure testing of pipes |
AS/NZS 4020:2002 | Testing of products for use in contact with drinking water |
AS/NZS 1462.15:1996 | Methods of test for PVC pipes and fittings Method for determination of vinyl chloride monomer content (Reconfirmed 2017) |
AS 1646.3-2000 | Elastomeric seals for waterworks purposes - Material requirements for pipe joints seals used in water and wastewater applications with the exception of natural rubber and polyisoprene compounds |
AS/NZS 1462.3:1998 | Methods of test for plastics pipes and fittings Method for determining the impact characteristics of pipes (Reconfirmed 2017) |
AS/NZS 1462.5:2002 | Methods of test for plastics pipes and fittings Vicat softening temperature (Reconfirmed 2017) |
AS 1145.2-2001 | Determination of tensile properties of plastics materials Test conditions for moulding and extrusion plastics |
AS/NZS 1462.14:1996 | Methods of test for PVC pipes and fittings Method for determination of the light transmission of pipe (Reconfirmed 2017) |
AS 5200.000-2006 | Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products (Reconfirmed 2018) |
AS 1646-2007 | Elastomeric seals for waterworks purposes (Reconfirmed 2018) |
AS/NZS 4798(INT):2005 | Polyethylene maintenance shafts |
MP 52-2005 | Manual of authorization procedures for plumbing and drainage products |
AS 4041-2006 | Pressure piping (Reconfirmed 2016) |
AS/NZS 3518:2004 | Acrylonitrile butadiene styrene (ABS) compounds, pipes and fittings for pressure applications |
AS 5200.000-2005 | Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products |
AS/NZS 3500.1:2003 | Plumbing and drainage Water services |
AS/NZS 2032:2006 | Installation of PVC pipe systems (Reconfirmed 2024) |
AS 2419.1-2005 | Fire hydrant installations System design, installation and commissioning |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.