AS/NZS 2803.1:1994

1 - AS/NZS 2803.1:1994 DOORS - SECURITY SCREEN - HINGED
4 - PREFACE
5 - CONTENTS
6 - FOREWORD
7 - SCOPE AND GENERAL
7 - 1 SCOPE
7 - 2 APPLICATION
7 - 3 REFERENCED DOCUMENTS
7 - 4 DEFINITIONS
7 - 4.1 Deadlocking bolt
7 - 4.2 Door frame
8 - 4.3 Door framing
8 - 4.4 Grille
8 - 4.5 Security screen door
8 - 4.5.1 Type I
8 - 4.5.2 Type II
8 - 4.5.3 Type III
8 - 5 DESIGN AND CONSTRUCTION
8 - 5.1 Galvanic compatibility
8 - 5.2 Corrosion protection
8 - 5.2.1 Steel
8 - 5.2.2 Aluminium
8 - 5.3 Door framing
8 - 5.4 Corner joints
8 - 5.5 Grille
8 - 5.5.1 Type I infill materials
9 - 5.5.2 Type II infill materials
10 - 5.5.3 Type III infill materials
12 - 5.6 Hinges
12 - 5.7 Rivets
12 - 5.8 Screws
12 - 5.9 Locks
12 - 5.10 Lock fitting
12 - 5.11 Dimensions
13 - 6 PERFORMANCE
13 - 7 MARKING
13 - 7.1 General
13 - 7.2 Installation instructions
14 - APPENDIX A - METHOD OF TEST TO MEET THE PERFORMANCE REQUIREMENTS OF THIS STANDARD
14 - A1 SCOPE
14 - A2 PRINCIPLE
14 - A3 TEST SAMPLE
14 - A3.1 General
14 - A3.2 Hinges
14 - A3.3 Lock fittings
15 - A4 PREPARATION FOR TESTING
15 - A5 APPARATUS
20 - A6 TEST PROCEDURE
20 - A6.1 General
20 - A6.2 Method of application of forces to the infill material
20 - A6.3 Attack upon locks
21 - A6.4 Hinge attack
21 - A6.5 Centre pull
21 - A6.6 Bottom pull
21 - A6.7 Top pull
22 - A6.8 Shear test on infill material (only applicable to Type I and Type II infill materials)
22 - A6.9 Type II infill material force probe test
22 - A7 REPORT
22 - A7.1 Supplementary information
28 - APPENDIX B - IDENTIFICATION DETAILS FOR DOORS SUBMITTED FOR TYPE TESTING IN ACCORDANCE WITH AS/NZS 2803.1 APPENDIX A
36 - APPENDIX C - TEST SEQUENCE FLOW CHART
37 - APPENDIX D - MARKING

Specifies requirements for the design, construction and performance of single leaf hinged security screen doors. It does not apply to double leaf doors nor does it deal with the installation of security screen doors. It includes an appendix for the method of test for resistance to forced entry. It is intended for use by regulatory authorities and all persons concerned with the manufacture, installation and general requirements of hinged security screen doors.

This Standard specifies requirements for the design, construction and performance of hinged security screen doors (single leaf only), primarily used in residential situations.NOTES1 Double leaf doors can be constructed and tested in accordance with Appendix A and reported accordingly, in consultation with the testing authority.2 The parts of a door shall not be referred to in isolation as being the complete door, for example, the grille.3 Requirements for the installation of hinged security screen doors are set out in AS 2804, Installation of hinged security screen doors, which is currently under revision and expected to be available in parts -hinged and sliding, as joint Australian/New Zealand Standards. The effectiveness of security screen doors is dependent on the strength of the door, the adequacy of its installation in the door frame, and surrounds.

First published as AS 2803-1985.
Second edition 1987.
Jointly revised and redesignated as Joint Standard AS/NZS 2803.1:1994.