AS/NZS 3750.2:2008
Current
The latest, up-to-date edition.
Paints for steel structures Ultra high-build paint (Reconfirmed 2020)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
English
19-05-2008
Important note : Users cannot be edited or removed once added to your Multi user PDF.Specifies requirements for two-component ultra high-build paints for the protection of iron and steel against exterior corrosion in aggressive service conditions.
| Committee |
CH-003
|
| DocumentType |
Standard
|
| ISBN |
0 7337 8660 X
|
| Pages |
16
|
| ProductNote |
Reconfirmed 11/09/2020.
This standard has been reconfirmed in Australia in 2020 and remains current in New Zealand. Reconfirmation Notice 11/09/2020 |
| PublisherName |
Standards Australia
|
| Status |
Current
|
| Supersedes |
This Standard specifies requirements for two-component ultra high-build paints for the protection of iron and steel against exterior corrosion in aggressive service conditions. They are suitable for application only by using high pressure, high volume airless spray equipment. Paints specified in this Standard comply with the requirements of Paint type C34 in AS/NZS 2312. These paints are produced in a limited colour range, usually white, grey or black.Ultra high-build (UHB) paints are classified as follows:(a) Type I, two-pack epoxy.(b) Type II, polyester.(c) Type III, vinyl ester.Ultra high-build paints are not intended to provide an aesthetically pleasing finish, but should provide long-term protection in aggressive atmospheric exposures for periods in excess of 15 years.NOTES:1 These paints may be used as detailed for system EPF1, in AS/NZS 2312.2 Appendix A contains recommendations which should be provided by the purchaser at the time of enquiry or order.3 Additional information on the use and application of ultra high-build paints is contained in Appendix B.
Originated as AS 3750.2-1994.
Revised and redesignated AS/NZS 3750.2:2008.
| AS/NZS 1580.103.1:1995 | Paints and related materials Methods of test - Examination and preparation of samples for testing (Reconfirmed 2013) |
| AS 2854-2004 | Tinplate cans for general use |
| AS/NZS 1580.101.1:1999 | Paints and related materials - Methods of test Conditions of test - Temperature, humidity and airflow control (Reconfirmed 2013) |
| AS 1580.408.5-2006 | Paints and related materials - Methods of test Adhesion - Pull-off test |
| AS 3894.12-2002 | Site testing of protective coatings Inspection report - Coating (Reconfirmed 2019) |
| AS 3894.1-2002 | Site testing of protective coatings Non-conductive coatings - Continuity testing - High voltage (brush) method (Reconfirmed 2013) |
| AS 1580.406.1-2004 | Paints and related materials - Methods of test Resistance to impact - Falling weight test (Gardner-type tester) |
| AS 1627.4-2005 | Metal finishing - Preparation and pretreatment of surfaces Abrasive blast cleaning of steel (Reconfirmed 2017) |
| AS 4352-2005 | Tests for coating resistance to cathodic disbonding |
| AS 1145.5-2001 | Determination of tensile properties of plastics materials Test conditions for fibre-reinforced plastic composites |
| AS/NZS 1580.211.1:1995 | Paints and related materials - Methods of test Degree of settling (Reconfirmed 2013) |
| AS 1145.3-2001 | Determination of tensile properties of plastics materials - Test conditions for films and sheets |
| AS 1145.2-2001 | Determination of tensile properties of plastics materials Test conditions for moulding and extrusion plastics |
| AS 1145.4-2001 | Determination of tensile properties of plastics materials Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| AS 1580.301.1-2005 | Paints and related materials - Methods of test Non-volatile content by mass |
| AS/NZS 2310:2002 | Glossary of paint and painting terms (Reconfirmed 2016) |
| AS 1580.403.2-2006 | Paints and related materials - Methods of test Abrasion resistance |
| AS 3894.13-2002 | Site testing of protective coatings Inspection report - Daily (Reconfirmed 2019) |
| AS 3894.10-2002 | Site testing of protective coatings Inspection report - Daily surface and ambient conditions (Reconfirmed 2019) |
| AS/NZS 2312:2002 | Guide to the protection of structural steel against atmospheric corrosion by the use of protective coatings |
| AS/NZS 1580.104.1:2000 | Paints and related materials - Methods of test Recommended materials for test panels (Reconfirmed 2013) |
| AS 3894.4-2002 | Site testing of protective coatings Assessment of degree of cure |
| AS 2714-1993 | The storage and handling of hazardous chemical materials - Class 5.2 substances (organic peroxides) |
| AS/NZS 1580.108.1:1994 | Paints and related materials - Methods of test Determination of dry film thickness on metallic substrates - Non-destructive methods (Reconfirmed 2013) |
| AS/NZS 1580.101.5:1999 | Paints and related materials - Methods of test Conditions of test - Temperature and humidity control (Reconfirmed 2013) |
| AS 2905-2005 | Steel drums |
| AS 3894.14-2002 | Site testing of protective coatings Inspection report - Daily painting (Reconfirmed 2019) |
| AS/NZS 1580.205.4:1998 | Paints and related materials - Methods of test Application properties - Airless spraying (Reconfirmed 2013) |
| AS 1145.1-2001 | Determination of tensile properties of plastics materials General principles |
| AS 3894.11-2002 | Site testing of protective coatings Equipment report (Reconfirmed 2019) |
| AS/NZS 5131:2016 | Structural steelwork - Fabrication and erection |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.