AS/NZS IEC 60079.15:2020
Current
The latest, up-to-date edition.
Explosive atmospheres Equipment protection by type of protection "n"
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
English
24-01-2020
Important note : Users cannot be edited or removed once added to your Multi user PDF.The objective of this Standard is to specify requirements for the construction, testing and marking for Group II electrical equipment with type of protection “n” which includes sealed devices “nC”, hermetically sealed devices “nC”, non-incendive components “nC” and restricted breathing enclosures “nR” intended for use in explosive gas atmospheres.
| Committee |
EL-014
|
| DevelopmentNote |
New PDF incorporating Amendment 1.
|
| DocumentType |
Standard
|
| ISBN |
978 1 76072 714 7
|
| Pages |
24
|
| ProductNote |
Modifies IEC 60079-15:2017 (ED.5.0). Redesignated from AS/NZS to AS/NZS IEC by Amendment 1.
|
| PublisherName |
Standards Australia
|
| Status |
Current
|
| Supersedes |
This part of IEC 60079 specifies requirements for the construction, testing and marking for
Group II electrical equipment with type of protection “n” which includes; sealed devices “nC”,
hermetically sealed devices “nC”, non-incendive components “nC” and restricted breathing
enclosures “nR” intended for use in explosive gas atmospheres. This part of IEC 60079
applies to electrical equipment where the rated input voltage does not exceed 15 kV r.m.s. AC or
DC including where the internal working voltages of the Ex product exceeds 15 kV, for example
starters for HID luminaires.
This part of IEC 60079 supplements and modifies the general requirements of IEC 60079-0,
except as indicated in Table 1. Where a requirement of this part of IEC 60079 conflicts with a
requirement of IEC 60079-0, the requirement of this part of IEC 60079 takes precedence.
Originated as AS/NZS 60079.15:2006.
Previous edition 2011.
Third edition 2020.
Reissued incorporating Amendment No 1 (November 2021).
| IEC 60050-426:2008 | International Electrotechnical Vocabulary (IEV) - Part 426: Equipment for explosive atmospheres |
| IEC 60297-3-105:2008 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-105: Dimensions and design aspects for 1U high chassis |
| IEC 60079-2:2014 | Explosive atmospheres - Part 2: Equipment protection by pressurized enclosure "p" |
| IEC 60297-3-104:2006 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-104: Connector dependent interface dimensions of subracks and plug-in units |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| IEC 60079-1:2014 | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
| IEC 60079-0:2017 | Explosive atmospheres - Part 0: Equipment - General requirements |
| IEC 60297-3-107:2012 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-107: Dimensions of subracks and plug-in units, small form factor |
| IEC 60297-3-101:2004 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-101: Subracks and associated plug-in units |
| IEC 60079-7:2015+AMD1:2017 CSV | Explosive atmospheres - Part 7: Equipment protection by increased safety "e" |
| IEC 61347-2-1:2000+AMD1:2005+AMD2:2013 CSV | Lamp controlgear - Part 2-1: Particular requirements for startingdevices (other than glow starters) |
| IEC 60297-3-100:2008 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-100: Basic dimensions of front panels, subracks, chassis, racks and cabinets |
| IEC 60297-3-102:2004 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-102: Injector/extractor handle |
| IEC 60297-3-103:2004 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-103: Keying and alignment pin |
| IEC 60297-3-106:2010 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 3-106: Adaptation dimensions for subracks and chassis applicable with metric cabinets or racks in accordance with IEC 60917-2-1 |
| IEC 60079-17:2013 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| AS 2809.1:2020 | Road tank vehicles for dangerous goods General requirements for all road tank vehicles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.