• Shopping Cart
    There are no items in your cart

ASTM A 1063/A1063M : 2017 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Steel Sheet, Twin-Roll Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process

Available format(s)

PDF

Superseded date

04-05-2020

Language(s)

English

Published date

01-01-2017

€74.48
Excluding VAT

CONTAINED IN VOL. 01.06, 2017 Defines steel sheet, produced by the Twin-Roll Cast Process and zinc-coated (galvanized) by the hot-dip process in coils and cut lengths.

Committee
A 05
DocumentType
Redline
Pages
13
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

1.1This specification covers steel sheet, produced by the Twin-Roll Cast Process (see Appendix X2) and zinc-coated (galvanized) by the hot-dip process in coils and cut lengths.

Note 1:See Appendix X2 for a description of the Twin-Roll Cast process.

1.2The product is produced in various zinc coating weights [masses] or coating designations as shown in Table 1.

(A)The coating designation number is the term by which this product is specified. Because of the many variables and changing conditions that are characteristic of continuous hot-dip coating lines, the zinc coating is not always evenly divided between the two surfaces of a coated sheet; nor is it always evenly distributed from edge to edge. However, the minimum triple-spot average coating weight (mass) on any one side shall not be less than 40 % of the single-spot requirement.
(B)As it is an established fact that the atmospheric corrosion resistance of zinc coated sheet products is a direct function of coating thickness (weight (mass)), the selection of thinner (lighter) coating designations will result in almost linearly reduced corrosion performance of the coating. For example, heavier galvanized coatings perform adequately in bold atmospheric exposure whereas the lighter coatings are often further coated with paint or a similar barrier coating for increased corrosion resistance. Because of this relationship, products carrying the statement “meets ASTM A1063/A1063Mrequirements” should also specify the particular coating designation.
(C)No minimum means that there are no established minimum requirements for triple- and single-spot tests.

1.3Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification A924/A924M unless otherwise provided herein.

1.4The product is available in a number of designations, grades and classes and in the two following general categories that are designed to be compatible with different application requirements.

1.4.1Steels with mandatory chemical requirements and typical mechanical properties.

1.4.2Steels with mandatory chemical requirements and mandatory mechanical properties.

1.5This material is available in the following sizes:

1.5.1Thickness—up to 0.078 in. [2.0 mm]

1.5.2Width—up to 79 in. [2000 mm]

1.6The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this specification.

1.7This specification is applicable to orders in either inch-pound units (as A1063) or SI units (as A1063M). Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other.

1.8Unless the order specifies the “M” designation (SI units), the product shall be furnished to inch-pound units.

1.9This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

CSA S136-12 PACKAGE : 2012 CONSISTS OF S136-12 - NORTH AMERICAN SPECIFICATION FOR THE DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS AND S136.1-12 - COMMENTARY ON NORTH AMERICAN SPECIFICATION FOR THE DESIGN OF COLD-FORMED STEEL STRUCTURAL MEMBERS
ASTM A 1092 : 2015 Standard Specification for Steel Sheet, as Cold-Reduced, for Conversion to Annealed Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel Sheet
ASTM A 754/A754M :2011 Standard Test Method for Coating Weight (Mass) of Metallic Coatings on Steel by X-Ray Fluorescence
BS ISO 15208:2012 Continuous hot-dip zinc-coated twin-roll cast steel sheet of commercial quality
AASHTO T 65M/T 65 : 2013 METHOD OF TEST FOR MASS [WEIGHT] OF COATING ON IRON AND STEEL ARTICLES WITH ZINC OR ZINC-ALLOY COATINGS
ISO 15208:2012 Continuous hot-dip zinc-coated twin-roll cast steel sheet of commercial quality
ASTM A 754/A754M : 2011 : R2016 Standard Test Method for Coating Weight (Mass) of Metallic Coatings on Steel by X-Ray Fluorescence
11/30234411 DC : 0 BS ISO 15208 - CONTINUOUS HOT-DIP ZINC-COATED TWIN-ROLL CAST STEEL SHEET OF COMMERCIAL QUALITY
BS ISO 15211:2012 Continuous hot-dip zinc-coated twin-roll cast steel sheet of structural quality and high strength steel
ISO 15211:2012 Continuous hot-dip zinc-coated twin-roll cast steel sheet of structural quality and high strength steel
ASTM A 1003/A1003M : 2015 : REDLINE Standard Specification for Steel Sheet, Carbon, Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members

ASTM B 852 : 2016 : REDLINE Standard Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.