ASTM A 1082/A1082M : 2016 : R2021
Current
The latest, up-to-date edition.
Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications
Hardcopy , PDF
English
14-10-2021
Committee |
A 01
|
DocumentType |
Standard
|
Pages |
6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification covers high strength stainless steel bolting materials and bolting components for special purpose applications such as pressure vessels. Several grades of precipitation-hardened and duplex (ferritic-austenitic) stainless steels are covered. Selection will depend upon design, service conditions, mechanical properties and characteristics related to the application.
1.2The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M.
1.3Supplementary Requirements are provided for use at the option of the purchaser. The Supplementary Requirements shall only apply when specified individually by the purchaser in the purchase order or contract.
1.4This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable “M” specification designation (SI units), the inch-pound units shall apply.
1.5The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM A 962/A962M : 2019 | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM A 370 : 2021 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 479/A479M : 2024 | Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels |
ASTM A 479/A479M : 2023 : REV A | Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels |
ASTM A 962/A962M : 2019 | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM A 370 : 2024 : REV A | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 962/A962M : 2023 : REV A | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM A 479/A479M : 2023 | Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels |
ASTM A 276/A276M : 2024 : REV A | Standard Specification for Stainless Steel Bars and Shapes |
ASTM A 962/A962M : 2022 | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM A 962/A962M : 2024 | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM A 370 : 2020 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 276/A276M : 2024 | Standard Specification for Stainless Steel Bars and Shapes |
ASTM A 276/A276M : 2017 | Standard Specification for Stainless Steel Bars and Shapes |
ASTM A 370 : 2023 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 479/A479M : 2020 | Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels |
ASTM A 479/A479M : 2021 | Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels |
ASTM A 276/A276M : 2023 | Standard Specification for Stainless Steel Bars and Shapes |
ASTM A 962/A962M : 2024 : REV A | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM A 370 : 2022 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM A 962/A962M : 2023 | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM A 370 : 2024 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.