ASTM A 1094/A1094M : 2020
Current
The latest, up-to-date edition.
Standard Specification for Continuous Hot-Dip Galvanized Steel Bars for Concrete Reinforcement
Hardcopy , PDF
English
09-09-2020
Committee |
A 01
|
DocumentType |
Standard
|
Pages |
5
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification covers steel reinforcing bars, with protective zinc or zinc-alloy coatings applied by the continuous hot-dip process.
Note 1:The galvanizer is identified throughout this specification as the manufacturer.
1.2Guidelines for construction practices at the job-site are presented in Appendix X1.
1.3Guidelines for use of continuous hot-dip galvanized reinforcing bars with non-galvanized steel forms are presented in Appendix X2.
1.4The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered requirements of the specification.
1.5This specification is applicable for orders in either inch-pound units (as Specification A1094) or SI units (as Specification A1094M).
1.6The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with this specification.
1.7This specification does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this specification to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM A 123/A123M : 2017 | Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products |
ASTM A 1055/A1055M : 2016 | Standard Specification for Zinc and Epoxy Dual-Coated Steel Reinforcing Bars |
ASTM A 615/A615M : 2020 | Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement |
ASTM B 6 : 2018 | Standard Specification for Zinc |
ASTM A 615/A615M : 2024 | Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement |
ASTM A 90/A90M : 2021 | Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings |
ASTM A 90/A90M : 2013 : R2018 | Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings |
ASTM B 487 : 2024 | Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section |
ASTM A 706/A706M : 2022 | Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement |
ASTM A 615/A615M : 2022 | Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement |
ASTM A 1035/A1035M : 2024 | Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement |
ASTM A 706/A706M : 2024 | Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement |
ASTM A 706/A706M : 2004 | Standard Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement |
ASTM B 852 : 2016 : EDT 1 | Standard Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel |
ASTM B 6 : 2023 | Standard Specification for Zinc |
ASTM B 487 : 2020 | Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section |
ASTM A 1035/A1035M : 2020 | Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement |
ASTM A 996/A996M : 2016 | Standard Specification for Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement |
ASTM A 1035/A1035M : 2023 | Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement |
ASTM A 1035/A1035M : 2023 : REV A | Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement |
ASTM A 996/A996M : 2024 | Standard Specification for Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement |
ASTM A 706/A706M : 2016 | Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement |
ASTM A 706/A706M : 2022 : REV A | Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement |
ASTM B 852 : 2016 : R2022 | Standard Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.