ASTM A 1124/A1124M : 2023
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Textured Epoxy-Coated Steel Reinforcing Bars
Hardcopy , PDF
23-08-2024
English
01-09-2023
Committee |
A 01
|
DocumentType |
Standard
|
Pages |
9
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This specification covers deformed steel reinforcing bars with protective epoxy coating applied by the electrostatic spray method followed by a texturing surface treatment material.
Note 1:The coating applicator is identified throughout this specification as the manufacturer.
1.2Other organic coatings and texturing surface treatment materials may be used provided they meet the requirements of this specification.
1.3Requirements for coatings are contained in Annex A1 of Specification A775/A775M.
1.4Requirements for texturing surface treatment material are contained in Annex A1.
1.5Requirements for patching material are contained in Annex A2 of Specification A775/A775M.
1.6Guidelines for construction practices at the job-site are presented in Appendix X1.
1.7This specification is applicable for orders in either inch-pound units (as Specification A1124) or SI units [as Specification A1124M].
1.8The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.9This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.10This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM G 14 : 2004 : R2024 | Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test) |
ASTM G 14 : 2004 : R2018 | Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test) |
ASTM A 615/A615M : 2024 | Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement |
ASTM G 20 : 2010 : R2019 | Standard Test Method for Chemical Resistance of Pipeline Coatings |
ASTM A 615/A615M : 2022 | Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement |
ASTM A 1035/A1035M : 2024 | Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement |
ASTM G 8 : 2024 | Standard Test Methods for Cathodic Disbonding of Coated Steel |
ASTM A 706/A706M : 2024 | Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement |
ASTM G 62 : 2023 | Standard Test Methods for Holiday Detection of Coatings used to Protect Pipelines |
ASTM D 374/D374M : 2016 | Standard Test Methods for Thickness of Solid Electrical Insulation |
ASTM G 8 : 1996 : R2019 | Standard Test Methods for Cathodic Disbonding of Pipeline Coatings |
ASTM B 117 : 2019 | Standard Practice for Operating Salt Spray (Fog) Apparatus |
ASTM A 996/A996M : 2016 | Standard Specification for Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement |
ASTM A 1035/A1035M : 2023 | Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement |
ASTM G 20 : 2010 : R2024 | Standard Test Method for Chemical Resistance of Pipeline Coatings |
ASTM A 1035/A1035M : 2023 : REV A | Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement |
ASTM D 374/D374M : 2023 | Standard Test Methods for Thickness of Solid Electrical Insulation |
ASTM A 996/A996M : 2024 | Standard Specification for Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement |
ASTM A 706/A706M : 2016 | Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement |
ASTM A 706/A706M : 2022 : REV A | Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.