ASTM A 193/A193M : 2024 : REV A
Current
The latest, up-to-date edition.
Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications
Hardcopy , PDF
English
15-10-2024
Committee |
A 01
|
DocumentType |
Standard
|
Pages |
14
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification2 covers alloy and stainless steel bolting materials and bolting components for pressure vessels, valves, flanges, and fittings for high temperature or high pressure service, or other special purpose applications. See Specification A962/A962M for the definition of bolting. Bars and wire shall be hot-wrought and may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be carbide solution treated or carbide solution treated and strain-hardened. When strain hardened austenitic stainless steel is ordered, the purchaser should take special care to ensure that Appendix X1 is thoroughly understood.
1.2Several grades are covered, including ferritic steels and austenitic stainless steels designated B5, B8, and so forth. Selection will depend upon design, service conditions, mechanical properties, and high temperature characteristics.
1.3The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M.
Note 1:The committee formulating this specification has included several steel types that have been rather extensively used for the present purpose. Other compositions will be considered for inclusion by the committee from time to time as the need becomes apparent.
Note 2:For grades of alloy-steel bolting suitable for use at the lower range of high temperature applications, reference should be made to Specification A354.
Note 3:For grades of alloy-steel bolting suitable for use in low temperature applications, reference should be made to Specification A320/A320M.
1.4Nuts for use with bolting are covered in Section 13.
1.5Supplementary Requirements are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified in the purchase order or contract.
1.6This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply.
1.7The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C 852/C852M : 2017 : R2022 | Standard Guide for Design Criteria for Plutonium Gloveboxes |
ASTM F 1476 : 2007 : R2019 | Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications |
ASTM A 962/A962M : 2024 | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM F 1565 : 2000 : R2019 | Standard Specification for Pressure-Reducing Valves for Steam Service |
ASTM F 2437/F2437M : 2017 : R2023 | Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs |
ASTM A 453/A453M : 2017 : R2024 | Standard Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels |
ASTM F 1718 : 2001 : R2019 | Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps |
ASTM F 1370 : 1992 : R2019 : EDT 1 | Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard |
ASTM F 1155 : 2010 : R2024 | Standard Practice for Selection and Application of Piping System Materials |
ASTM F 38 : 2018 : R2024 | Standard Test Methods for Creep Relaxation of a Gasket Material |
ASTM F 2798 : 2009 : R2023 | Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications |
ASTM A 354 : 2017 : EDT 2 | Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners |
ASTM F 1276 : 2023 | Standard Test Method for Creep Relaxation of Laminated Composite Gasket Materials |
ASTM C 1533 : 2015 : R2022 | Standard Guide for General Design Considerations for Hot Cell Equipment |
ASTM F 1510 : 2021 | Standard Specification for Rotary Positive Displacement Pumps, Ships Use |
ASTM B 994/B994M : 2022 | Standard Specification for Nickel-Cobalt Alloy Coating |
ASTM F 3394/F3394M : 2023 | Standard Specification for Hardened Steel Backup and Reaction Washers Inch and Metric Dimensions<rangeref></rangeref > |
ASTM C 1725 : 2017 : R2022 | Standard Guide for Hot Cell Specialized Support Equipment and Tools |
ASTM F 2716 : 2008 : R2020 | Standard Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam |
ASTM F 1508 : 1996 : R2021 | Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services |
ASTM F 998 : 2012 : R2022 | Standard Specification for Centrifugal Pump, Shipboard Use |
ASTM A 320/A320M : 2024 : REV A | Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service |
ASTM A 962/A962M : 2024 : REV A | Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range |
ASTM F 606/F606M : 2024 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
ASTM F 606/F606M : 2021 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.