• Shopping Cart
    There are no items in your cart

ASTM A 194/A194M : 2020 : REV A

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both

Available format(s)

Hardcopy , PDF

Superseded date

14-06-2022

Superseded by

ASTM A 194/A194M : 2022

Language(s)

English

Published date

03-06-2020

€74.48
Excluding VAT

Committee
A 01
DocumentType
Standard
Pages
12
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

1.1This specification2 covers a variety of carbon, alloy, and martensitic stainless steel nuts in the size range 1/4through 4 in. and metric M12 through M100 nominal. It also covers austenitic stainless steel nuts in the size range 1/4in. and M12 nominal and above. These nuts are intended for high-pressure or high-temperature service, or both. Grade substitutions without the purchaser's permission are not allowed.

1.2Bars from which the nuts are made shall be hot-wrought. The material may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be solution annealed or annealed and strain-hardened. When annealed and strain hardened austenitic stainless steel is ordered in accordance with Supplementary Requirement S1, the purchaser should take special care to ensure that 8.2.2, Supplementary Requirement S1, and Appendix X1 are thoroughly understood.

1.3Supplementary requirements of an optional nature are provided. These shall apply only when specified in the inquiry, contract, and order.

1.4This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.

1.5The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Within the text, the SI units are shown in brackets.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F 1510 : 2021 Standard Specification for Rotary Positive Displacement Pumps, Ships Use
ASTM F 2716 : 2008 : R2020 Standard Practice for Comparison of Nonmetallic Flat Gaskets in High Pressure Saturated Steam
ASTM F 1476 : 2007 : R2019 Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications
ASTM A 962/A962M : 2019 Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range
ASTM F 1718 : 2001 : R2019 Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
ASTM F 1554 : 2020 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength
ASTM F 2798 : 2009 : R2018 Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications
ASTM A 320/A320M : 2021 : REV A Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service
ASTM F 998 : 2012 : R2018 Standard Specification for Centrifugal Pump, Shipboard Use
ASTM A 193/A193M : 2020 Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications
ASTM F 1508 : 1996 : R2021 Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services
ASTM A 563/A563M : 2021 : REV A : EDT 1 Standard Specification for Carbon and Alloy Steel Nuts (Inch and Metric)
ASTM F 1565 : 2000 : R2019 Standard Specification for Pressure-Reducing Valves for Steam Service
ASTM F 2437/F2437M : 2017 Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs
ASTM F 1155 : 2010 : R2019 Standard Practice for Selection and Application of Piping System Materials
ASTM F 432 : 2019 Standard Specification for Roof and Rock Bolts and Accessories
ASTM B 695 : 2021 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
ASTM F 1370 : 1992 : R2019 : EDT 1 Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard
ASTM F 3125/F3125M : 2021 Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength

ASTM A 370 : 2021 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM F 606/F606M : 2019 Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
ASTM B 695 : 2004 : R2016 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
ASTM A 320/A320M : 2018 Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service
ASTM A 370 : 2020 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM B 695 : 2021 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
ASTM A 370 : 2011 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
ASTM A 320/A320M : 2021 Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service
ASTM E 112 : 2013 : R2021 Standard Test Methods for Determining Average Grain Size
ASTM E 112 : 2013 Standard Test Methods for Determining Average Grain Size
ASTM F 606/F606M : 2021 Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
ASTM A 320/A320M : 2021 : REV A Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.