ASTM A 20/A20M : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for General Requirements for Steel Plates for Pressure Vessels
Hardcopy , PDF
20-11-2017
English
15-11-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
33
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This general requirements specification2 covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following product specifications issued by ASTM:
| Title of Specification | ASTM DesignationA |
| Pressure Vessel Plates, Alloy Steel, Nickel | A203/A203M |
| Pressure Vessel Plates, Alloy Steel, Molybdenum | A204/A204M |
| Pressure Vessel Plates, Alloy Steel, Manganese- | A225/A225M |
| Stainless Chromium Steel-Clad Plate | A263 |
| Stainless Chromium-Nickel Steel-Clad Plate | A264 |
| Nickel and Nickel-Base Alloy-Clad Steel Plate | A265 |
| Pressure Vessel Plates, Carbon Steel, Low- and | A285/A285M |
| Pressure Vessel Plates, Carbon Steel, Manganese-Silicon | A299/A299M |
| Pressure Vessel Plates, Alloy Steel, Manganese- | A302/A302M |
| Pressure Vessel Plates, Alloy Steel, Double- | A353/A353M |
| Pressure Vessel Plates, Alloy Steel, Chromium- | A387/A387M |
| Pressure Vessel Plates, Carbon Steel, High Strength | A455/A455M |
| Pressure Vessel Plates, Carbon Steel, for Intermediate- | A515/A515M |
| Pressure Vessel Plates, Carbon Steel, Moderate- and | A516/A516M |
| Pressure Vessel Plates, Alloy Steel, High-Strength, | A517/A517M |
| Pressure Vessel Plates, Alloy Steel, Quenched and | A533/A533M |
| Title of Specification | ASTM DesignationA |
| Pressure Vessel Plates, Heat-Treated, Carbon- | A537/A537M |
| Pressure Vessel Plates, Alloy Steel, Quenched-and- | A542/A542M |
| Pressure Vessel Plates, Alloy Steel, Quenched and | A543/A543M |
| Pressure Vessel Plates, Alloy Steel, Quenched and | A553/A553M |
| Pressure Vessel Plates, Carbon Steel, Manganese- | A562/A562M |
| Pressure Vessel Plates, Carbon Steel, High Strength, for | A612/A612M |
| Pressure Vessel Plates, 5 % and 51/2% Nickel Alloy | A645/A645M |
| Pressure Vessel Plates, Carbon-Manganese-Silicon | A662/A662M |
| Pressure Vessel Plates, Carbon-Manganese-Silicon | A724/A724M |
| Pressure Vessel Plates, Low-Carbon Age-Hardening | A736/A736M |
| Pressure Vessel Plates, High-Strength Low-Alloy Steel | A737/A737M |
| Pressure Vessel Plates, Heat-Treated, Carbon- | A738/A738M |
| Pressure Vessel Plates, Alloy Steel, Chromium- | A832/A832M |
| Steel Plates for Pressure Vessels, Produced by | A841/A841M |
| Steel Plates, 9 % Nickel Alloy, for Pressure Vessels, | A844/A844M |
| Pressure Vessel Plates, Alloy Steel, Chromium- | A1017/A1017M |
1.1.1This general requirements specification also covers a group of supplementary requirements that are applicable to several of the above product specifications as indicated therein. Such requirements are provided for use if additional testing or additional restrictions are required by the purchaser, and apply only if specified individually in the purchase order.
1.2Appendix X1 provides information on coil as a source of plates for pressure vessels.
1.3Appendix X2 provides information on the variability of tensile properties in plates for pressure vessels.
1.4Appendix X3 provides information on the variability of Charpy-V-Notch impact test properties in plates for pressure vessels.
1.5Appendix X4 provides information on cold bending of plates, including suggested minimum inside radii for cold bending.
1.6These materials are intended to be suitable for fusion welding. When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized.
1.7In case of any conflict in requirements, the requirements of the applicable product specification prevail over those of this general requirements specification.
1.8Additional requirements that are specified in the purchase order and accepted by the supplier are permitted, provided that such requirements do not negate any of the requirements of this general requirements specification or the applicable product specification.
1.9For purposes of determining conformance with this general requirements specification and the applicable product specification, values are to be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.
1.10The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.11This general requirements specification and the applicable product specification are expressed in both inch-pound units and SI units; unless the order specifies the applicable “M” specification designation (SI units), the plates are to be furnished to inch-pound units.
1.12This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.