ASTM A 285/A285M : 2024
Current
The latest, up-to-date edition.
Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength
Hardcopy , PDF
English
15-10-2024
Important note : Users cannot be edited or removed once added to your Multi user PDF.| Committee |
A 01
|
| DocumentType |
Standard
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification2 covers carbon steel plates of low- and intermediate-tensile strengths which may be killed or semi-killed at the producer’s option. These plates are intended for fusion-welded pressure vessels.
1.2Plates under this specification are available in three grades having different strength levels as follows:
| Grade | Tensile Strength, ksi [MPa] |
| A | 45–65 [310–450] |
| B | 50–70 [345–485] |
| C | 55–75 [380–515] |
1.3The maximum thickness of plates is limited by the capacity of the composition to meet the specified mechanical property requirements.
Note 1:For killed carbon steels only, refer to the following ASTM specifications:3
A299/A299M Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon
A515/A515M Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service
A516/A516M Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
1.4For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply.
1.5The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ANSI/AWWA C520:2024 | Knife Gate Valves, Sizes 2 In. (50 mm) Through 96 In. (2,400 mm) |
| ASTM A 672/A672M : 2019 | Standard Specification for Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures |
| ASTM A 134/A134M : 2019 | Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over) |
| ASTM F 1007 : 2018 : R2022 | Standard Specification for Pipeline Expansion Joints of the Packed Slip Type for Marine Application |
| ASTM F 1603 : 2017 : R2023 | Standard Specification for Kettles, Steam-Jacketed, 32 oz to 20 gal (1 to 75.7 L), Tilting, Table Mounted, Direct Steam, Gas and Electric Heated |
| ASTM F 1602 : 2012 : R2023 | Standard Specification for Kettles, Steam-Jacketed, 20 to 200 gal (75.7 to 757 L), Floor or Wall Mounted, Direct Steam, Gas and Electric Heated |
| ASTM D 2485 : 2022 | Standard Test Methods for Evaluating Coatings For High Temperature Service |
| ASTM A 671/A671M : 2020 | Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures |
| ASTM A 20/A20M : 2020 | Standard Specification for General Requirements for Steel Plates for Pressure Vessels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.